Panasonic Switch-M8ePWR PN27089KA Скачать руководство пользователя | Manualshive

Страница: 169 / 194

background image

169

Available commands are listed below.

S Set the IP address of the TFTP server that executes upload/download the configuration

file.

Press "S." The command prompt changes to "Enter IP address of TFTP server>."
Enter an IP address of TFTP server.

F Set the name of the configuration file to be uploaded/downloaded.

Press "F." The command prompt changes to "Enter file name>." Specify the file
name of the downloaded program in 30 half-width characters or less.

U Start the upload of the configuration file.

Press "U." The command prompt changes to "Upload file(Y/N)>." Confirm whether
or not to start the process. Press "Y" to start the process. Press "N" to cancel the
upload.

D Start the download of the configuration file.

Press "D." The command prompt changes to "Download file(Y/N)>." Confirm
whether or not to start the process. Press "Y" to start the download. Press "N" to
cancel the download.

Q Return to the previous menu.

«
...
167
168
169
170
171
...
»

Содержание Switch-M8ePWR PN27089KA



































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Switch-M8ePWR PN27089KA

Бренд: Watchguard Страницы: 40

Бренд: Salusfin Страницы: 6

Бренд: CSS Страницы: 2

Бренд: QNO Страницы: 106

Бренд: Face Страницы: 8

Бренд: TRENDnet Страницы: 2

Бренд: TRENDnet Страницы: 2

Бренд: ZyXEL Communications Страницы: 2

Бренд: ZyXEL Communications Страницы: 263

Бренд: Lanpro Страницы: 6

ibaBM-FOX-i-3o-D

Бренд: IBA Страницы: 13

Бренд: Adeunis RF Страницы: 9

Бренд: NETGEAR Страницы: 232

3GStation Carrier

Бренд: Ubiquiti Страницы: 24

Бренд: East Coast Datacom Страницы: 13

SwyxConnect 1722

Бренд: Swyx Страницы: 112

Бренд: Eagle Eye Страницы: 61

Бренд: Kasda Страницы: 7

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды