Panasonic PT-JW130FBE, Инструкция по эксплуатации (Функциональное руководство)

Страница: 184 / 217

Chapter 5 Operations — Content Manager
184 - ENGLISH
f
Upload the backed up schedules to all projectors for simultaneous playback.
Acquiring and delivering schedules using “Multi Projector Monitoring & Control Software”
Using “Multi Projector Monitoring & Control Software”, you can deliver and register the same schedules in other
projectors while the SD card with the duplication source schedules is inserted in the SD card slot of the projector.
“Multi Projector Monitoring & Control Software” is included in the supplied CD-ROM.
1) Start up “Multi Projector Monitoring & Control Software”.
f
If the target projector is not registered, follow “Projector Registration” in the Operating Instructions of “Multi
Projector Monitoring & Control Software” to register the projector.
2) Acquire the signage schedule from the duplication source projector.
3) Deliver the signage schedule to the duplication destination projector or a group.
Note
f
For the procedure of acquiring and delivering schedules, refer to “Acquiring and Delivering a Signage Schedule” in the Operating
Instructions of “Multi Projector Monitoring & Control Software”.
Setting synchronization for the NTP server
To perform simultaneous playback of the same schedule in multiple projectors continuously, synchronize the
projectors with the NTP server and adjust the date and time setting of target projectors.
The projector is equipped with the NTP server function. By using one of multiple projectors of this model as the
NTP server function, the time of other projectors can be synchronized, under the environment where access to the
external NTP server is not possible.
1) Start up the web browser on the computer.
2) Access the projector from the web browser.
f
For the procedure of accessing the projector from the web browser, refer to “Accessing from the web
browser” (
x
page 105).
3) On the [Adjust clock] page of the web control screen, select [Time Zone].
f
The schedule is played back based on the local date and time set in the projector. Set the same time zone
for the projectors performing simultaneous playback.
4) On the [Adjust clock] page of the web control screen, set [NTP SYNCHRONIZATION] to [ON].
5) Enter the IP address or server name of the NTP server in [NTP SERVER NAME] of the [Adjust clock]
page.
f
To use one of multiple projectors of this model as the NTP server, enter the IP address set for the projector.
f
To enter the server name, the DNS server needs to be set up. For setting the DNS server, refer to “[Network
config] page” (
x
page 112).
f
For details on setting the NTP server, refer to “[Adjust clock] page” (
x
page 114).
6) Click the [Set date and time] button on the [Adjust clock] page to apply the setting.
f
After a while, the projector is synchronized with the time of the NTP server.
Note
f
To use the projector as the NTP server, set [NTP SYNCHRONIZATION] to [OFF], and then set the date and time.
f
The settings of [Time Zone], [NTP SYNCHRONIZATION], [Date], and [Time] on the [Adjust clock] page can also be configured from the
[SETUP] menu → [DATE AND TIME] (
x
page 74). The NTP server can be set only on the [Adjust clock] page of the web control screen.
f
For details on a computer that can be used for setting the web control screen, refer to “Computer that can be used for setting”
(
x
page 105).
f
If you use the projector as the NTP server, approximately 15 minutes are required after configuring the synchronization setting of other
projectors till completing synchronization. After configuring the synchronization setting, wait for more than 15 minutes before starting
playback of the schedule.
f
When the projector is used as the NTP server, approximately 15 minutes are required before completing synchronization if the time setting
of the NTP server is changed. Keep this in mind when operating the simultaneous playback of the schedule.