Panasonic PAW-160MAH3M Скачать руководство пользователя

Страница: 85 / 92

AHU Kit – Installation Instructions – 07/2023

Trouble diagnosis

8.2

Specific error codes for PACi

Remote

Controller

Display

Description

Detailed Explanation

L02

Indoor & outdoor unit type

mismatched

Setting error, indoor / outdoor unit type / model mismatched

8.3

Specific error codes for ECOi

Remote

Controller

Display

Description

Detailed Explanation

L02

Connected indoor unit is

not a multi unit.

Either AHU kit is PACi type or parameter 2C not properly set.

L05

Priority setting trouble

2 or more indoor units set as priority (priority indoor unit).

L06

Priority setting trouble

2 or more indoor units set as priority (non priority indoor unit).

P01

Fan protection error

Thermal protection for AHU fan motor is activated

Terminal contacts OP3 & K2 open (respectively T20 connector no the AHU main PCB A1)

8.4

Error codes for outdoor units

For all error codes not mentioned here, please check in the service manual of the corresponding

outdoor unit model. The meaning of those error codes might be different by specific outdoor unit

model.

8.5

Special displays on the wired remote controller

Blinking Exclamation mark display

Automatic backup is in progress. A/C units can be operated. Check error history in the outdoor unit (see service manual

of the corresponding outdoor unit) for the original trouble alarm.

Energy saving display

Energy saving is on to control energy consumption.*

The operation capacity of the outdoor unit is restricted.

Units are operated at the capacity set by schedule.*

Can only be set using the “Panasonic H&C Control App”

The display of “operation capacity of the outdoor unit is restricted” is typically shown while the

0 – 10 V demand control is active.
For further details about CZ-RTC6BL please refer to the operation maual of the remote controller.

Содержание PAW-160MAH3M





























































































Результаты поиска

Содержание PAW-160MAH3M

Отзывы:

Похожие инструкции для PAW-160MAH3M

Бренды по названию

Популярные бренды

Panasonic PAW-160MAH3M, Руководство по установке

Результаты поиска

Содержание PAW-160MAH3M

Отзывы:

Похожие инструкции для PAW-160MAH3M

Бренды по названию

Популярные бренды