Panasonic PAW-160MAH3M Скачать руководство пользователя

Страница: 32 / 92

AHU Kit – Installation Instructions – 07/2023

Product description

System Overview – ECO G systems

Single-connection

or multiple-connection

systems

A AHU Kit enclosure (complete)

B AHU system (field supplied)

C Remote controller (integrated in AHU Kit enclosure)

D Outdoor unit

E Liquid piping (field supplied)

F Gas piping (field supplied)

G Electronic expansion valve

H Thermistor for liquid pipe (E1)

Thermistor for gas pipe (E3)

J Thermistor for suction air (TA)

K Thermistor for discharge air (BL)

L Inter-unit wiring

M Magnetic relay for operating the blower (field sup

plied)

1 Single-connection system shown here as an example.

Multi-connection systems are possible in combination with PAW-160MAH3M or PAW-280MAH3M. In case of multi-

connections with PAW-560MAH3M further restrictions will apply. For details, please contact your local Panasonic service

partner.

System Overview – PACi and PACi NX systems

Single-connection

system only

A AHU Kit enclosure (complete)

B AHU system (field supplied)

C Remote controller (integrated in AHU Kit enclosure)

D Outdoor unit

E Liquid piping (field supplied)

F Gas piping (field supplied)

G Thermistor for liquid pipe (E1)

H Thermistor for heat exchanger pipe middle (E2)

Thermistor for suction air (TA)

J Inter-unit wiring

K Magnetic relay for operating the blower (field sup

plied)

L Strainer (liquid pipe & gas pipe) min. Ø 25.4 mm (field

supplied)

1 With all PACi and PACi NX outdoor units only 1-to-1 installations are allowed.

Содержание PAW-160MAH3M





























































































Результаты поиска

Содержание PAW-160MAH3M

Отзывы:

Похожие инструкции для PAW-160MAH3M

Бренды по названию

Популярные бренды

Panasonic PAW-160MAH3M, Руководство по установке

Результаты поиска

Содержание PAW-160MAH3M

Отзывы:

Похожие инструкции для PAW-160MAH3M

Бренды по названию

Популярные бренды