Panasonic EverVolt Standard EVAC-105-4 Скачать руководство пользователя страница 14

Страница: 14 / 76

Installation Manual

System Layout & Dimensions

66" x 24" x 10.5" (Battery) & 17.5" x 39" x 6" (Inverter)

Planning for Installation

Knockout Locations

There are multiple knockouts on

the inverter and battery enclosure

(as shown with the red arrows.)

1", 1.5", 1.75"

.5", .75", 1", 1.5" (four locations

underneath the inverter).

Planning for Installation

1. Essential Load Sizing:

Please ensure that the battery power per the

EverVolt spec sheet is capable of running the essential load circuits

during backup.

2. Internet Connectivity:

All EverVolt systems ship with a PLC

communications kit for simple installation. EverVolt also works with

a CAT5/6 hardwired cable to the customer's internet router. Cellular

modem connectivity is an option that will be available in the future.

If interested please contact your sales representative for more

information.

3. System Placement:

(a) Placement of the physical system so that

the batteries rest on the feet of the battery enclosure (b) a conduit

between the battery and inverter be placed for easy routing of the 1/0

or 2/0 wire. The clearance spacing needs to be observed to allow for

adequate cooling and servicing of the equipment as shown below.

4. Outlet Placement:

120V AC outlet needs to be within 4 ft of the

inverter to plug in the power supply to the PowerHub.

1.5" & 2" (four locations, two

on each side of the battery

enclosure).

Содержание EverVolt Standard EVAC-105-4













































































Результаты поиска

Содержание EverVolt Standard EVAC-105-4

Отзывы:

Похожие инструкции для EverVolt Standard EVAC-105-4

Бренды по названию

Популярные бренды

Panasonic EverVolt Standard EVAC-105-4, Руководство по установке

Результаты поиска

Содержание EverVolt Standard EVAC-105-4

Отзывы:

Похожие инструкции для EverVolt Standard EVAC-105-4

Бренды по названию

Популярные бренды