Panasonic EverVolt Standard EVAC-105-4 Скачать руководство пользователя страница 7

Страница: 7 / 76

Installation Manual

WARNING.

Charge EverVolt only within the specified

conditions (e.g. temperature range, voltage, current, etc.)

Failure to do so may result in damages, heat generation,

smoke, fire, or explosion.

Check the positive (+) and negative (-) terminals. If EverVolt

is connected with reversed polarity, unexpected reactions

may occur such as damages, heat generation, smoke, fire, or

explosion.

Do not connect between the positive (+) and negative (-)

terminals with a conductive material (e.g. wire, a cable, etc.).

This may result in damages, heat generation, smoke, fire, or

explosion.

Do not directly solder the EverVolt. This may result in

damages, heat generation, smoke, fire, or explosion.

WARNING:

Risk of electric shock. Risk of fire. Do not attempt

to repair the battery(ies); it contains no user-serviceable

parts. Tampering with or opening the battery(ies) will void

the warranty. If the battery(ies) fails, contact Panasonic at

[email protected]

WARNING:

Proper disposal of lithium-ion batteries is

required. Please contact your Panasonic representative for

disposal and recycling measures.

WARNING:

Take care when lifting the Battery. The Battery is

heavy and may require a lifting tool to initially lift the battery

high enough to get a good hold on it.

Important Safety Warnings

Содержание EverVolt Standard EVAC-105-4













































































Результаты поиска

Содержание EverVolt Standard EVAC-105-4

Отзывы:

Похожие инструкции для EverVolt Standard EVAC-105-4

Бренды по названию

Популярные бренды

Panasonic EverVolt Standard EVAC-105-4, Руководство по установке

Результаты поиска

Содержание EverVolt Standard EVAC-105-4

Отзывы:

Похожие инструкции для EverVolt Standard EVAC-105-4

Бренды по названию

Популярные бренды