Palfinger MBB C 1000 S Скачать руководство пользователя

Страница: 143 / 196

143

Box-type, Universal

or Reversible Unit:

To check the oil level:



Lower the tail lift so that the platform touches the ground.



If required, retract all stabilizer feet.



Remove the cover from the unit.



Using the indicator at the oil reservoir or the dip stick, check
whether the indication is within the prescribed marked
range.



If required, refill oil up to level mark.



Re-install the cover of the unit.

Checking the Bolts and Nuts for Tight Seat



Check whether all bolts and nuts are seated tightly.



Especially observe all bearing pins and associated bolts
and all fastening elements of the auxiliary frame and the tail
lift mounting!



Retighten any loose bolts and nut.

Checking the Screw fittings and Pipes of the
Hydraulic System



Check all screw fittings and pipes of the hydraulic system.
Make sure that the screws are tight and the hydraulic lines
undamaged.



Retighten any loose screws.



Replace damaged hydraulic hoses immediately.



Replace all hydraulic hoses after three years at the latest.
The manufacture date is stamped on the fittings.

Checking the Bellows



Make sure that the two bellows are in a good condition and
undamaged and that they are tightly fit to the piston rod and
cylinder.



Replace damaged bellows immediately.

All Models

A BC F G KL M V

All Models

Betriebsanleitung_Hubladebuehnen_EN.book Seite 143 Donnerstag, 15. August 2019 4:04 16

Содержание MBB C 1000 S





































































































































































































Результаты поиска

Содержание MBB C 1000 S

Отзывы:

Похожие инструкции для MBB C 1000 S

Бренды по названию

Популярные бренды

Palfinger MBB C 1000 S, Руководство по эксплуатации

Результаты поиска

Содержание MBB C 1000 S

Отзывы:

Похожие инструкции для MBB C 1000 S

Бренды по названию

Популярные бренды