Palfinger MBB C 1000 S Скачать руководство пользователя

Страница: 51 / 196

Lifting the Hydraulic Underrun Bumper



Turn the rotary switch

(30)

upwards until the underrun

bumper has reached its upper end position.

Opening the Platform



Loosen the platform interlock (if present).



Turn the rotary switches

(27)

and

(29)

simultaneously

downward and hold them down until the platform has
reached the horizontal operating position.

If an optional load safety device is present, the platform is
lowered and then unfolds to the horizontal operating posi-
tion.

Lowering the Platform



Turn the rotary switches

(27)

and

(29)

simultaneously

downward and hold them in this position until the platform
has made contact with the ground.

After the platform has touched the ground it tilts and adjusts
to the ground.

Lifting the Platform



Turn the rotary switches

(27)

and

(29)

simultaneously up-

ward and hold them in this position until the platform has
reached the vehicle loading floor height.

The platform tilts to the horizontal or preset position before
it is lifted.

Closing the Platform



Turn the rotary switches

(28)

and

(29)

simultaneously up-

ward and hold them in this position until the platform is
closed.

If an optional load safety device is present, the platform
closes approximately to 80° and is lowered a small amount.
Finally, it moves to the vertical transport position and is
lifted into the load safety device.



Close the platform interlock (if present).

Lowering the Hydraulic Underrun Bumper



Turn the rotary switch

(30)

downwards until the underrun

bumper has reached its lower end position.

Betriebsanleitung_Hubladebuehnen_EN.book Seite 51 Donnerstag, 15. August 2019 4:04 16

Содержание MBB C 1000 S





































































































































































































Результаты поиска

Содержание MBB C 1000 S

Отзывы:

Похожие инструкции для MBB C 1000 S

Бренды по названию

Популярные бренды

Palfinger MBB C 1000 S, Руководство по эксплуатации

Результаты поиска

Содержание MBB C 1000 S

Отзывы:

Похожие инструкции для MBB C 1000 S

Бренды по названию

Популярные бренды