Palfinger MBB C 1000 S Скачать руководство пользователя

Страница: 9 / 196

Observe the Following

General Notes

• Always have these instructions readily available in the vehi-

cle.

• Constructional changes may only be performed by the con-

tractor repair shop of

PALFINGER Tail Lifts

. You will find the

address of your local contractor repair shop and other con-
tact information in the list of repair shops.

• For maintenance, use only original spare parts from

PALFIN-

GER Tail Lifts

• Observe all applicable accident prevention regulations.

When Switching On

• Before switching on the tail lift, check whether all safety and

warning devices are in place and function properly.

• Warning flags
• Warning lights
• Supporting straps
• Roll stops

During Operation

• Make sure that the tail lift is unlocked before taking it into op-

eration.

• Provide sufficient illumination of the loading area.
• Never transport persons on the tail lift.
• Always load the tail lift is such a way that the weight is evenly

distributed.

• Secure the load so that it cannot fall off the tail lift. Rolling

containers without brakes may only be transported on the tail
lift if you secure them with roll stops (roll-off protection)
against rolling away.

• Keep the maneuvering area around the vehicle free.

Betriebsanleitung_Hubladebuehnen_EN.book Seite 9 Donnerstag, 15. August 2019 4:04 16

Содержание MBB C 1000 S





































































































































































































Результаты поиска

Содержание MBB C 1000 S

Отзывы:

Похожие инструкции для MBB C 1000 S

Бренды по названию

Популярные бренды

Palfinger MBB C 1000 S, Руководство по эксплуатации

Результаты поиска

Содержание MBB C 1000 S

Отзывы:

Похожие инструкции для MBB C 1000 S

Бренды по названию

Популярные бренды