- 6.3a -
5 mm
5 mm
- 6.3b -
B
A
0, 5 cm
B
A
5 mm
- 6.4 -
2 m
3,5 - 4 m min
0,4 m
INSTALLATION
6.2
EARTHING
The Ecomonoblocco is equipped with a screw for the
equipotential connection which can hold a cable with a
section from 2.5 mm
2
to 6 mm
2
, to be used to obtain
equipotentiality of the earth in compliance with current
VWDQGDUGV7KLV¿[WXUHLVORFDWHGRQWKHORZHUSDUWRIWKH
Ecomonoblocco and is indicated by the symbol
.
$OVRWKHÀXHPXVWEH¿WWHGZLWKDRZQHDUWKLQFRPSOLDQFH
to the standards in force.
6.3 HEIGHT
ADJUSTMENT
7RDGMXVWWKH¿QDOKHLJKWRIWKH(FRPRQREORFFRFODGGLQJ
¿UHEHGKHLJKWMXVWWXUQWKHDGMXVWPHQWVFUHZVORFWHG
on the base. Adjsut the screws
)LJD$DGMXVWPHQW
VFUHZ%¿UHEHGKHLJKWXQWLOWKHPDUEOHFRYHUSUR¿OHRQ
the Ecomonoblocco is at the proper height compared to
WKHFODGGLQJPDNLQJVXUHWKDWWKHERWWRPRIWKH¿UHSODFH
LVOHYHO)RUFODGGLQJZLWK¿UHEHG+FPUHPRYHWKH
adjustment screws. Where featured, the lever for the
adjustment of combustion air must be about 0.5 cm over
the cladding surface, so that it is easily usable. (Fig. 6.3b).
6.4
SMOKE EXHAUST SYSTEM
The Ecomonoblocco must be connected to a smoke
exhaust system so as to ensure combustion products are
suitably discharged into the atmosphere, in accordance
with standards EN 1856-1-2 EN 1857, EN 1443 EN
13384-1-3, EN 12391-1 and UNI 10683, both as regards
sizing and the construction materials used.
The CHIMNEY must be sized as described on the
datasheet (average draught 12 Pa with door closed).
The components making up the combustion
product exhaust system must be declared as being
VXLWDEOH IRU WKH VSHFL¿F RSHUDWLQJ FRQGLWLRQV DQG
marked (declaration of conformity or European
technical approval for the product).
7KHÀXHPXVWKDYHDFRQVWDQWFURVVVHFWLRQDORQJ
its entire height.
The minimum recommended height is 3.5 to 4 m
(Fig. 6.4).
A collection chamber should be featured at the bottom of
WKHÀXHWRFROOHFWDQ\VROLGUHVLGXHVDQGFRQGHQVDWH
,03529,6('ÀXHVPDGHXVLQJXQVXLWDEOHPDWHULDOVDUH
illegal and affect correct operation of the Ecomonoblocco.
A
PERFECT DRAUGHT
LVDERYHDOOWKHUHVXOWRIDÀXH
that is clear of obstructions such as chokes, horizontal
sections or corners; any axial displacements should be
at a maximum angle of 45° compared to the vertical axis,
(better still if it is only 30°). These displacements should
preferably be effected near the chimney top (Fig. 6.5).
The
SMOKE
FRQQHFWLRQEHWZHHQWKH¿UHSODFHDQG
ÀXHVKRXOGKDYHWKHVDPHFURVVVHFWLRQDVWKHVWRYH¶V
VPRNHRXWOHW7KHVPRNH¿WWLQJPXVWEHVHDOHGDQGWKH
XVHRIÀH[LEOHPHWDOOLFSLSHVLVSURKLELWHG&KDQJHVLQ
direction in respect to the smoke outlet of the appliance
must be executed using elbows not exceeding 45° in
respect to vertical.
The
CHIMNEY TOP
shall be the
WINDPROOF
type
with an inside cross section equivalent to that of the
ÀXH DQG ZLWK D VPRNH RXWOHW SDVVDJH VHFWLRQ DW OHDVW
34
cod. 004771651 MBL - 06/2015 - Palazzetti - PN - Italy
