PACOM PDR16-PC, Руководство пользователя

Страница: 14 / 96

User’s Manual
8
6. Move to each number ( 1-32 ), and select the camera number to sequence from a drop-down list (from Camera 1 to
Camera 16 and Not used ).
7. Move to Hold spot during single-screen mode , and check the box if you do not want the cameras sequence on
the Spot monitor while the main monitor is set to the single-screen display mode.
8. Move to Include event display , and check the box if you want to display the event-detected video during spot
sequence.
9. Move to
Show video loss
, and check the box if you want to show the video loss image during spot sequence.
10. Move to Sequence dwell , and set the sequence dwell time (from 1 to 10 seconds) for the main monitor by
holding down and dragging the pointer. If you set the value to 3 seconds for the Sequence dwell, the camera
display will sequence every three seconds on the Main monitor.
11. Move to Event monitoring dwell , and set the monitoring dwell time (from 0 to 10 seconds) for the event-driven
image by holding down and dragging the pointer. If you set the value to 3 seconds for the Event monitoring
dwell, the camera with an event will display in the one-screen mode for three seconds on the main monitor any
time an event (alarm input or motion detection) occurs. Set the value to
0
seconds if you do not want the
event-driven camera to be displayed in the one-screen mode.
12. Move to
Auto deletion
, and check the box if you want to delete the video recorded earlier than user-defined
period.
13. If you check the Auto deletion box, move to Period and set the period to keep the recorded video. e.g. If you
check the Auto deletion box, and set 30 days in the Period box, the DVR will automatically delete the video
which is older than 30 days from the current day.
14. Move to Show OSD , and check the box if you want to display OSD information on the image. OSD information
includes camera title, recording mode and recording status.
NOTE: An R indicates the target camera is in the Time-lapse recording schedule mode. An S indicates it is in
the Event-driven recording mode. An RS indicates it is in the Time & Event recording mode. An R located at the
bottom-right corner indicates the DVR is recording video, and the blink rate of the R relates to the recording
speed.
15. Move to
Remote control , and check the box when the DVR is controlled remotely using RS232C or RS485
communications signals. See Appendix 6 – Protocol for Remote Controlling DVR for details.
16. If you check the Remote control box, click the Set up Remote control... button. Select the DVR's COM port
to use from the drop-down list. Click the Set up port... button, and set the Baud rate from 300 to 256,000. Select
Parity from None , Even or Odd parity. Select Data bit from 7 bit or 8 bit format. Select Stop bit from 1 bit or
2 bits from the drop-down list. Move to Device ID , and set the device ID number from 0 to 127 using the slide
bar. You can save your changes by clicking the OK button. Selecting Cancel exits the dialog box without saving
the changes.
17. Move to HDD usage , and select either Once or Recycle . When Once is selected, the DVR stops recording
when the hard disk drive is full. When Recycle is selected, the DVR continues recording when the hard disk
drive is full by overwriting the oldest video.
18. Click the Set up Time Sync… button, and set up the time synchronization if required. See Appendix 8 – Time
Synchronization for details.
19. Click the
Set up backup...
button, and set up backup information. See the
SmartBackup
section.
20. Click the Set up pager... button, and set up pager information. See the SmartPager section.
NOTE: The Set up pager... button will be activated if you set up SmartPager to start in the SmartGuard setup.
21. Click the
Set up Web Server... button, and set up an Apache Web Server for the WebGuard program.
22. Click the Load... button if you want to load typical settings. Click the Save... button if you want to save settings.
Click the Default button if you want to load default settings. You can save your changes by clicking the OK
button. Selecting Cancel exits the dialog box without saving the changes.
NOTE: Only the administrator level user can use the Load, Save and Default buttons.