Pacific energy TOFINO i20 Maxitrol G6R страница 47 Скачать руководство пользователя

Страница: 47 / 56

Artisan Front Trim Installation

The Artisan Front comes with a trim piece

which mounts between the Artisan Front and
the Backing plate. To Install the trim piece and
the Artisan Front:

1. Mount the backing plate to the fireplace as

shown in on page 46.

2. Mount the Trim piece to the rear side of

the Artisan Front as indicated in Figure 124.

3. Mount the Artisan Front and the trim piece

onto the backing plate as shown in Figure

125.

Artisan Front

Trim for
Artisan Front

Backing Plate

Figure 123: Artisan front, front trim and backing plate.

Artisan Front

Tabs toward
backing plate

Mount trim piece
to back of front

Tabs toward
backing plate

Figure 124: Trim piece mounts to rear of Front.

Figure 125: Artisan front and trim assembled to

backing plate.

100000328

041119-56

i20 TOFINO

Содержание TOFINO i20 Maxitrol G6R

























































Результаты поиска

Содержание TOFINO i20 Maxitrol G6R

Отзывы:

Похожие инструкции для TOFINO i20 Maxitrol G6R

Бренды по названию

Популярные бренды

Pacific energy TOFINO i20 Maxitrol G6R, Руководство по установке

Результаты поиска

Содержание TOFINO i20 Maxitrol G6R

Отзывы:

Похожие инструкции для TOFINO i20 Maxitrol G6R

Бренды по названию

Популярные бренды