manualshive.com logo in svg

Pacific energy TOFINO i20 Maxitrol G6R, Руководство по установке

Поделиться
Скачать
Pacific energy TOFINO i20 Maxitrol G6R Скачать руководство пользователя страница 16

 Panel Installation 

The panel sets are delicate and should be handled with care.

The baffle and panel support bracket (Figure 22) retains the side panels, supports the front end of the ceramic 

glass baffle, and has a shield which directs the light from the ceiling of the firebox (available on i20s models 
only) down onto the log set (model dependent). It is held in place by two bolts. The bracket and its bolts 
should be removed before installing the rear and side panels so that the bolts protruding from the ceiling do 
not damage the panels. 

 

Figure 22:  Baffle and panel bracket.

Push tab against panel

Figure 23:  Perforated panel tab.

Side panel support tabs

Baffle support tabs

Figure 24:  Baffle and panel bracket supporting side  

 panels.

Rear panel support posts / 
support posts for rear end
 of ceramic glass baffle

Figure 25:  Rear wall showing panel support posts.

Note: The baffle and panel bracket (Figure 22) has a perforated tab at each end (Figure 23). This allows 
the tabs to be easily bent against the decorative side wall panels to hold them in place if necessary. 
Use only enough force to hold the panel in place and not so much as to damage the panel. 

16

041119-56 100000328

i20 TOFINO

Содержание TOFINO i20 Maxitrol G6R

























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды