Pacific energy TOFINO i20 Maxitrol G6R страница 3 Скачать руководство пользователя

Страница: 3 / 56

Important Note for the Commonwealth of Massachusetts:

From Massachusetts Rules and Regulations 248 5.08:

(a)

For all side wall horizontally vented gas fueled equipment installed in every dwelling, building or structure used in whole or

in part for residential purposes, including those owned or operated by the Commonwealth and where the side wall exhaust

vent termination is less than seven (7) feet above finished grade in the area of the venting, including but not limited to decks

and porches, the following requirements shall be satisfied.

INSTALLATION OF CARBON MONOXIDE DETECTORS. At the time of installation of the side wall horizontal vented gas

fueled equipment,the installing plumber or gas fitter shall observe that a hard wired carbon monoxide detector with an alarm

and battery back-up is installed on the floor level where the gas equipment is to be installed, in addition, the installing

plumber or gas fitter shall observe that a battery operated or hard-wired carbon monoxide detector with an alarm is installed

on each additional level of the dwelling, building or structure served by the side wall horizontal vented gas fueled equipment.

It shall be the responsibility of the property owner to secure the services of qualified licensed professionals for the installation

of hard-wired carbon monoxide detectors.

In the event that the side wall horizontally vented gas fueled equipment is installed in a crawl space or an attic, the hard-

wired carbon monoxide detector with alarm and battery back-up may be installed on the next adjacent floor level.

In the event that the requirements of this subdivision cannot be met at the time of completion of installation, the owner shall

have a period of thirty (30) days to comply with the above requirements; provided, however, that during said thirty (30) day

period, a battery operated carbon monoxide detector with an alarm shall be installed.

APPROVED CARBON MONOXIDE DETECTORS. Each carbon monoxide detector as required in accordance with the above

provisions shall comply with NFPA 720 and be ANSI/UL 2034 listed as IAS certified.

SIGNAGE. A metal or plastic identification plate shall be permanently mounted to the exterior of the building at a minimum

height of eight (8) feet above grade directly in line with the exhaust vent terminal for the horizontally vented gas fueled

heating appliance or equipment. The sign shall read, in print size no less than one-half (1/2) inch in size, “GAS VENT

DIRECTLY BELOW. KEEP CLEAR OF ALL OBSTRUCTIONS”.

INSPECTION. The state or local gas inspector of the side wall horizontally vented gas fueled equipment shall not approve

the installation unless, upon inspection, the inspector observes carbon monoxide detectors and signage installed in accor

dance with the provisions of 248 CMR 5.089(2) (a) 1 through 4.

(b)

EXEMPTIONS. The following equipment is exempt from 248 CMR 5.089(2)(a) 1 through 4.

The equipment listed in Chapter 10 entitled “Equipment Not Required To Be Vented” in the most current edition of NFPA 54

as adopted by the Board; and

Product Approved side wall horizontal vented gas fueled equipment installed in a room or structure separate from the

dwelling, building or structure used in whole or in part for residential purposes.

(c)

MANUFACTURER REQUIREMENTS – GAS EQUIPMENT VENTING SYSTEM PROVIDED. When the manufacturer of Product

Approved side wall horizontally vented gas equipment provides a venting system design or venting system components with

the equipment, the instructions provided by the manufacturer for installation of the equipment and the venting system shall

include:
1.

Detailed instructions for the installation of the venting system design or the venting system components; and

A complete parts list for the venting system design or venting system.

(d)

MANUFACTURER REQUIREMENTS – GAS EQUIPMENT VENTING SYSTEM NOT PROVIDED. When the manufacturer of a

Product Approved side wall horizontally vented gas fueled equipment does not provide the parts for venting the fuel

gases, but identifies “special venting systems”, the following requirements shall be satisfied by the manufacturer.

The referenced “special venting system” instructions shall be included with the appliance or equipment installation

instructions; and

The “special venting systems” shall be Product Approved by the Board, and the instructions for that system shall include a

parts list and detailed installation instructions.

(e)

A copy of all installation instructions for all Product Approved side wall horizontally vented gas fueled equipment, all venting

instructions, all parts lists for venting instructions, and/or all venting design instructions shall remain with the appliance or

equipment at the completion of the installation.

100000328

041119-56

i20 TOFINO

Содержание TOFINO i20 Maxitrol G6R

























































Результаты поиска

Содержание TOFINO i20 Maxitrol G6R

Отзывы:

Похожие инструкции для TOFINO i20 Maxitrol G6R

Бренды по названию

Популярные бренды

Pacific energy TOFINO i20 Maxitrol G6R, Руководство по установке

Результаты поиска

Содержание TOFINO i20 Maxitrol G6R

Отзывы:

Похожие инструкции для TOFINO i20 Maxitrol G6R

Бренды по названию

Популярные бренды