Pacific energy TOFINO i20 Maxitrol G6R страница 1 Скачать руководство пользователя

Страница: 1 / 56

WARNING: If the information in these

instructions is not followed exactly a fire

or explosion may result causing property
damage, personal injury or death.

INSTALLER:
Leave this manual with the appliance.
CONSUMER:
Retain this manual for future reference.

This appliance is suitable for installation in a

bedroom or bed sitting room.

This appliance may be installed in an after-

market permanently located, manufactured
home (USA only) or mobile home, where not
prohibited by local codes.

This appliance is only for use with the type of

gas indicated on the rating plate. This appliance

is not convertible for use with other gases
unless a certified kit is used.

FOR YOUR SAFETY

Do not store or use gasoline or other flammable
vapours and liquids in the vicinity of this or any
other appliance.

WHAT TO DO IF YOU SMELL GAS

•  Do not try to light any appliance.
•  Do not touch any electrical Switch.
•  Do not use any phone in your building.
•  Immediately call your gas supplier from a

neighbour’s phone. Follow the gas supplier’s
instructions.

• If you cannot reach your gas supplier call the

fire department.

Installation and service must be performed by
a qualified installer, service agency or the gas
supplier.

TOFINO

TOFINO

INSTALLATION
INSTRUCTIONS

MODEL: TOFINO i20
(SIT & Maxitrol G6R versions)

SERIES: A

DIRECT VENT GAS INSERT

Visit www.pacificenergy.net for the most recent version of this manual

100000328-50

041119-56

INSTALLATION INSTRUCTIONS

Содержание TOFINO i20 Maxitrol G6R

























































Результаты поиска

Содержание TOFINO i20 Maxitrol G6R

Отзывы:

Похожие инструкции для TOFINO i20 Maxitrol G6R

Бренды по названию

Популярные бренды

Pacific energy TOFINO i20 Maxitrol G6R, Руководство по установке

Результаты поиска

Содержание TOFINO i20 Maxitrol G6R

Отзывы:

Похожие инструкции для TOFINO i20 Maxitrol G6R

Бренды по названию

Популярные бренды