Pacific energy TOFINO i20 Maxitrol G6R страница 46 Скачать руководство пользователя | Manualshive

Страница: 46 / 56

background image

Surround Installation/Removal Instructions

Installation

1. Attach the ON/OFF Switch face plate to the backing plate before seating the backing plate onto the fire-

place.

2. Place the backing plate onto the fireplace by inserting its four hooks into the four slots on the fireplace

frame (Figure 121).

3. Install the Standard front by inserting its four hooks into the corresponding slots on the backing plate

Removal

Removal is the reverse of installation.

Figure 119: Standard Front.

Figure 120: Backing plate.

Figure 121: Mounting the backing plate.

Figure 122: Mounting the decorative front.

46

041119-56 100000328

i20 TOFINO

«
...
44
45
46
47
48
...
»

Содержание TOFINO i20 Maxitrol G6R

























































Отзывы:

Нет отзывов

Похожие инструкции для TOFINO i20 Maxitrol G6R

Бренд: Paloform Страницы: 17

Бренд: Rinnai Страницы: 21

CANTERBURY CANTIB-02-LP

Бренд: Cannon Страницы: 12

Бренд: Napoleon Страницы: 40

Бренд: Uniflame Страницы: 12

Бренд: Uniflame Страницы: 8

Бренд: Valcourt Страницы: 28

Бренд: Comfort Flame Страницы: 70

Бренд: Mendota Страницы: 45

Бренд: Desa Страницы: 40

CHIMENEA SRCH06D

Бренд: BIGHORN Страницы: 8

Бренд: Evonicfires Страницы: 29

Бренд: Saey Страницы: 44

Бренд: Lennox Hearth Products Страницы: 16

Бренд: Century Heating Страницы: 30

Бренд: Waterford Страницы: 24

Бренд: Tulikivi Страницы: 2

Бренд: Tulikivi Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды