background image

8.  

Recommended Planetary Gear Oil

Field  experience,  supported  by  extensive  engineering
tests, indicates the use of the proper planetary gear oil is
essential to reliable and safe operation of the brake and
obtaining long gear train life.

For simplicity, we have listed readily available products in
each temperature range which has been tested and found
to  meet  our  specifications.   This  is  not  to  say  that  other
lubricant brands would not perform equally as well.

If the following lubricant brands are not available in your
area,  make  certain  your  lubricant  vendor  supplies  you
with oil that is equivalent to those products listed below.

Planetary  winches  are  factory  filled  with  Exxon  Spartan
EP 150 or equivalent.

9. 

Periodic Teardown/ Inspection

We recommend that the hoist be disassemble for a thor-
ough inspection of all wear items every 2,000 hours of
operation or twelve (12) months, whichever occurs first.

10

PREVAILING AMBIENT TEMPERATURE

o

F -40     -30     -20     -10       0       10      20      30      40      50      60      70      80      90     100     110     120     130 

o

F

AGMA 5 EP, ISO VG 220

AGMA 4 EP, ISO VG 150

MOBILGEAR SHC 150 

SYNTHETIC OR EQUIVALENT

o

C -40             -30             -20             -10                0                10               20          

30              40               50        

o

C

NOTE: 

SHADED TEMPERATURE RANGE IN THE CHART ABOVE NOT RECOMMENDED FOR SEVERE APPLICATIONS SUCH AS: OFFSHORE 

CRANES, SUSTAINED FAST DUTY CYCLES OR FREQUENT LIFTING.

i

Texaco

Shell

Meropa 150

Meropa 220

Omala 150

Omala 220

Chevron

Gear Compounds EP 150

Gear Compounds EP 220

PREVAILING AMBIENT TEMPERATURE

o

F -40     -30     -20     -10       0       10      20      30      40      50      60      70      80      90     100     110     120     130 

o

F

AGMA 5 EP, ISO VG 220

AGMA 4 EP, ISO VG 150

SYNTHETIC OR EQUIVALENT

o

C -40             -30             -20             -10                0                10               20          

30              40               50        

o

C

NOTE: 

SHADED TEMPERATURE RANGE IN THE CHART ABOVE NOT RECOMMENDED FOR SEVERE APPLICATIONS SUCH AS: OFFSHORE 

CRANES, SUSTAINED FAST DUTY CYCLES OR FREQUENT LIFTING.

i

Texaco

Shell

Meropa 150

Meropa 220

Omala 150

Omala 220

Chevron

Gear Compounds EP 150

Gear Compounds EP 220

Texaco

Mobil

Shell

Meropa 150

Meropa 220

Omala 150

Omala 220

Chevron

Gear Compounds EP 150

Gear Compounds EP 220

MOBILGEAR 600 XP 220 OR EQUIVALENT

MOBILGEAR 600 XP 150 OR EQUIVALENT

Mobilgear 600 XP 150

Mobilgear 600 XP 220

Planetary hoists are factory filled with Mobilgear 600 XP 150, or equivalent. Consult your oil supplier for other equivalent
oils if required.

Failure to use the proper type and viscosity of plane-
tary gear oil may contribute to intermittent brake slip-
page which could result in property damage, severe
personal injury or death.  Some gear lubricants con-
tain large amounts of EP (extreme pressure) and anti-
friction  additives  which  may  contribute  to  brake  slip-
page and damage to brake friction discs or seals.  Oil
viscosity with regard to ambient temperatures is also
critical to reliable brake operation.  Our tests indicate
that excessively heavy or thick gear oil may contribute
to intermittent brake slippage.  Make certain that the
gear oil viscosity used in your hoist is correct for your
prevailing ambient temperature.

Gear Oil Capacity
-01 and -02 drums = 2 Pints (0.9 L)

Содержание BRADEN Gearmatic BG6A




































Отзывы: