manualshive.com logo in svg

Oxford Instruments Mercury iTC, Руководство пользователя

Поделиться
Скачать
Oxford Instruments Mercury iTC Скачать руководство пользователя страница 72

Handbook

November 2011 

/

 59-UMC0071 

/

 Issue 

01

 

Mercury 

iTC

Page 72

FUNCTIONAL DESCRIPTION

Original Instructions

The sensor and a reference resistor (either R44 or R45) are connected in series. Digital 
to analogue converters (DACs) U24 and U25 generate an upper and lower demand 
voltage. The upper voltage is buffered by U10 and applied to the upper end of the 
sensor resistor. The lower voltage is buffered by U15 and applied to the lower end of the 
reference resistor. The same current thus passes through the sensor and the reference 
resistor.

U7 and U11 measure the voltage across the sensor and feed the inputs of ADC U12. 
The outputs of U7 and U11 are also fed back to U10 and U15. This ensures that the 
voltage across the sensor is exactly equal to the demand voltage generated by U24 and 
U25.

U13 and either U14 or U16 measure the voltage across the reference resistor. This 
differential voltage is scaled by a reference gain multiplier, whose gain is selected to 
give an output in the range 1 V to 2.5 V. This voltage is then passed to the reference 
voltage inputs of the ADC (U12). This circuit configuration produces a ratiometric 
measurement technique. The resistance of the sensor is:

Rsensor

= 

Rref

 x |

ADCnorm

| x 

RefGain

/

ADCgain

Where:

Rref

 is the reference resistance (either 2k

Ω

 or 80k

Ω

).

ADCnorm

 is the ADC reading, normalised to the range 0 to ±1 V.

RefGain

 is the interpolated gain from the calibration tables.

ADCgain

 is the gain setting of the ADC.

The measurement accuracy of this circuit does not depend on the accuracy of the 
excitation or reference voltages. The accuracy primarily depends on the accuracy of the 
reference resistor plus any errors introduced by operational amplifiers.

Содержание Mercury iTC



















































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды