manualshive.com logo in svg

OTE VS 2001, Техническое руководство

Поделиться
Скачать
OTE VS 2001 Скачать руководство пользователя страница 141

VS 2001

Technical Handbook

Accessories

P/N: 779-0373/02
Revision 02

Marconi Proprietary information

Page 113

7.4

 

FUNCTIONAL TEST

 A suitable test bench must be prepared in order to carry out the test procedures.
The list of required items, except the terminal to be tested, is given below.

•

 

Reference auxiliary hand-held equipment PUMA TETRA or any other TETRA
terminal.

•

 Reference 

microphone.

•

 Reference 

loudspeaker.

•

  Reference TETRA Base Station. This base station must be located in a

suitable area in order to guarantee the radio link with the above equipment. It
must be configured to have in its database an identifier number for a dummy
(test) radio that can be configured each time a radio is tested in order to verify
its operation.

•

 

PC installed with the software to configure the equipment to be tested and
with the parameters of the radio base station.

•

 

Cable for the equipment downloading.

Содержание VS 2001













































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды