OTE VS 2001 Скачать руководство пользователя страница 14

VS 2001
Technical Handbook

List of tables

Page xiv

Marconi Proprietary information

P/N: 779-0373/02

Revision 02

List of tables

Tab. 1.1: Acronyms related to Fig. 1.1 ............................................................................................. 3
Tab. 1.2: Technical characteristics................................................................................................. 14
Tab. 1.2: Technical characteristics (Cont’d)................................................................................... 15
Tab. 1.3: VS 2001 main components ............................................................................................. 16
Tab. 2.1: J02 connector description ............................................................................................... 28
Tab. 2.1: J02 connector description (Cont’d) ................................................................................. 29
Tab. 2.2: J04 connector description ............................................................................................... 29
Tab. 2.3: Base Band frequencies ................................................................................................... 33
Tab. 2.4: R/T frequencies............................................................................................................... 38
Tab. 2.5: Pins function of J02 connector........................................................................................ 41
Tab. 2.6: Pin out connector J1 ....................................................................................................... 51
Tab. 2.7: Pin out connector J2 ....................................................................................................... 51
Tab. 2.8: Pin out connector J3 ....................................................................................................... 51
Tab. 3.1: P01 Rear connector pin functions................................................................................... 67
Tab. 3.2: Pin functions of J1........................................................................................................... 68
Tab. 3.3: Pin functions of J2........................................................................................................... 69
Tab. 3.4: DB37 connector pin out................................................................................................... 70
Tab. 3.5: PEI connector pin functions ............................................................................................ 71
Tab. 3.6: P04 connector pin functions............................................................................................ 71
Tab. 6.1: Summary of the preventive maintenance operations ..................................................... 88
Tab. 7.1: Parameters.................................................................................................................... 101
Tab. 7.2: Portable radio VS 2001 troubleshooting ....................................................................... 103
Tab. 7.3: Description of the symbols used in the troubleshooting flow diagrams........................ 104
Tab. 8.1: Summary of the corrective maintenance operations .................................................... 123
Tab. A.1: Microphone characteristics ........................................................................................... 135
Tab. A.2: Microphone connector pin out....................................................................................... 136
Tab. A.3: Loudspeaker characteristics ......................................................................................... 137
Tab. A.4: Handset characteristics................................................................................................. 140
Tab. A.5: MAM2000 connector pin out ......................................................................................... 142
Tab. A.6: GPS antenna characteristics ........................................................................................ 143

 

Содержание VS 2001













































































































































































Отзывы: