ORTEC DSPEC Pro Скачать руководство пользователя страница 84

Страница: 84 / 108

DSPEC Pro

Digital Gamma-Ray Spectrometer User’s Manual

794380D / 0914

SHOW_DELAY_SAMPLE

Shows the Delay Sample setting. See also SET_DELAY_SAMPLE.
Responses:
$C00003090

The sample number is 00003, and 090 is the checksum.

SHOW_DET_SNUM

This command responds with the detector serial number stored in the SMART-1 DIM.
Response:
$FP40175

Serial number P40175.

SHOW_DET_VERSION

Returns the DIM firmware version.
Examples:
$FNAID000

NaI DIM firmware version.

$FSMDT000

SMART-1 firmware version.

SHOW_DEVICE

Shows the currently selected device. Always 1 for DSPEC Pro.

SHOW_DISPLAY

Not used; included for backward compatibility.

SHOW_ETP

Reports if Enhanced Throughput Mode is enabled.
Responses:
$IF

Enhanced Throughput Mode disabled.

$IT

Enhanced Throughput Mode enabled.

SHOW_FEATURES

Responds with four 32-bit masks indicating which features are present in the MCB. See
Appendix 3.3 for a complete description of each bit in the mask.
Example Response:
FEATURES 02285062207 02014941185 00000000000 00000000000

SHOW_GAIN_ADJUST

Returns the gain-stabilizer amplifier setting.

SHOW_GAIN_CHANNEL

Reports the current center channel for the stabilizer gain peak. See also
SET_GAIN_CHANNEL.

Содержание DSPEC Pro













































































































Результаты поиска

Содержание DSPEC Pro

Отзывы:

Похожие инструкции для DSPEC Pro

Бренды по названию

Популярные бренды

ORTEC DSPEC Pro, Руководство пользователя по оборудованию

Результаты поиска

Содержание DSPEC Pro

Отзывы:

Похожие инструкции для DSPEC Pro

Бренды по названию

Популярные бренды