ORTEC DSPEC Pro Скачать руководство пользователя страница 48

Страница: 48 / 108

DSPEC Pro

Digital Gamma-Ray Spectrometer User’s Manual

794380D / 0914

Security State of Health

This is OK if the security test was passed at the end of the last spectrum acquisition. This is
available only for SMART-1 detectors.

Power State of Health

This is OK if the power to the DIM was constant during the last spectrum acquisition.

+24 volts

This is the current value of the +24 volt supply in the DIM as delivered to the detector.

+12 volts

This is the current value of the +12 volt supply in the DIM as delivered to the detector.

12 volts

This is the current value of the -12 volt supply in the DIM as delivered to the detector.

24 volts

This is the current value of the -24 volt supply in the DIM as delivered to the detector.

High Voltage

This is the current value of the high voltage bias supply in the DIM as delivered to the
detector.

Detector temperature

This is the detector temperature at the time the current spectrum acquisition stopped. This is
available only for SMART-1 detectors.

Live detector temperature

This is the detector temperature at the current time. This is available only for SMART-1
detectors.

Battery voltage

Not used in the DSPEC Pro.

Battery % full

Not used in the DSPEC Pro.

Battery time remaining

Not used in the DSPEC Pro.

Содержание DSPEC Pro













































































































Результаты поиска

Содержание DSPEC Pro

Отзывы:

Похожие инструкции для DSPEC Pro

Бренды по названию

Популярные бренды

ORTEC DSPEC Pro, Руководство пользователя по оборудованию

Результаты поиска

Содержание DSPEC Pro

Отзывы:

Похожие инструкции для DSPEC Pro

Бренды по названию

Популярные бренды