Omron NE1A-EDR01 Скачать руководство пользователя страница 47

Страница: 47 / 109

Troubleshooting

Section 3-2

Indicators/Display

Error

Cause

ED Router

operation

Error

code
(hex)

Countermeasures

NS D

NS E 7-seg-

ment

DeviceNet Communications-related Errors

---

Lit red ---

Node
address
duplication
error

The ED Router
DeviceNet node
address is the
same as the
node address
set for another
device.

DeviceNet opera-
tion stops.

0211 Check the node addresses

and the network connections
for all devices on the
DeviceNet network.

---

Lit red ---

Bus OFF
error

A DeviceNet bus
OFF error was
detected.

DeviceNet com-
munications stop.

0340 Check the DeviceNet net-

work for short-circuiting and
check the baud rate.

---

Not lit ---

DeviceNet
network
power sup-
ply error

The DeviceNet
network power
supply is OFF.

DeviceNet com-
munications stop
until the network
power supply is
restored.

0341 Check the DeviceNet net-

work power supply and the
communications cable con-
nections.

---

Flash-
ing
red

---

DeviceNet
communica-
tions timeout
error

Data could not
be sent in
DeviceNet for
1 s or longer.

DeviceNet com-
munications stop
until normal com-
munications are
restored.

0342 Check the following items:

• Is the baud rate the same

for each node?

• Are the cable lengths (main

and branch lines) correct?

• Are any cables discon-

nected or loose?

• Is terminating resistance

connected at both ends of
the main line?

Settings-related Error

Flash-
ing
red

---

Ethernet
basic setting
error

An error
occurred in the
data set for the
TCP/IP Configu-
ration.

Operation contin-
ues, using the
default values for
the TCP/IP Con-
figuration.

03D0 Check the Ethernet settings.

Flash-
ing
red

---

DeviceNet
node
address set-
ting changed
during oper-
ation

The node
address switch
setting was
changed during
operation.

Operation contin-
ues, using the
value from before
the change.

0214 Check the node address

switch setting. If the error
persists after the correct set-
ting has been made, replace
the ED Router.

Flash-
ing
red

---

Flash-
ing
red

IP address
setting
changed dur-
ing operation

The IP address
switch setting
was changed
during operation.

Operation contin-
ues, using the
value from before
the change.

0214 Check the IP address switch

setting. If the error persists
after the correct setting has
been made, replace the ED
Router.

Flash-
ing
red

---

Baud rate
setting
changed dur-
ing operation

The baud rate
switch setting
was changed
during operation.

Operation contin-
ues, using the
value from before
the change.

0214 Check the baud rate switch

setting. If the error persists
after the correct setting has
been made, replace the ED
Router.

Содержание NE1A-EDR01














































































































Результаты поиска

Содержание NE1A-EDR01

Отзывы:

Похожие инструкции для NE1A-EDR01

Бренды по названию

Популярные бренды

Omron NE1A-EDR01, Руководство по эксплуатации

Результаты поиска

Содержание NE1A-EDR01

Отзывы:

Похожие инструкции для NE1A-EDR01

Бренды по названию

Популярные бренды