Omron NE1A-EDR01 Скачать руководство пользователя страница 51

Страница: 51 / 109

Error History

Section 3-3

3-3-2

Error History Code List

Error

code
(hex)

Error

Detailed information

Non-

volatile

memory

1st byte

2nd byte

0118 Illegal message discarded

FF hex

Not stored

020F Ethernet communications controller

error

00 hex

01 hex

Stored

0211 Ethernet IP address duplication error

Port No.
(Ethernet: 02 hex)

Rightmost 8 bits of IP address
(hex)

Stored

0211 DeviceNet node address duplication

error

Port No.
(DeviceNet: 03 hex)

Node address (hex)

Stored

0214 DeviceNet node address setting

changed during operation

Port No.
(DeviceNet: 03 hex)

Node address (hex) detected as
changed

Stored

0214 IP address setting changed during

operation

Port No.
(Ethernet: 03 hex)

Rightmost 8 bits of IP address
(hex) detected as changed

Stored

0214 Baud rate setting changed during

operation

00 hex

Value (hex) detected as changed Stored

0214 Invalid IP address setting

FF hex

Stored

021A Device parameter error

00 hex

OE hex: Unit name

Stored

0340 Bus OFF error

00 hex

Not stored

0341 DeviceNet network power supply

error

00 hex

Not stored

0342 DeviceNet communications timeout

error

00 hex

Not stored

03C4 Server connection error

04 hex: BOOTP

01 hex: Specified host does not
exist.

02 hex: No such service at speci-
fied host.

03 hex: Timeout

06 hex: Host name resolution
error

07 hex: Transmission error

08 hex: Reception error

09 hex: Other error

0A hex: Obtaining IP address
error

Not stored

03D0 Ethernet basic setting error

01 hex: Ethernet setting
error

02 hex: TCP/IP basic set-
ting error

01 hex: CRC error

11 hex: Invalid IP address

12 hex: Invalid subnet mask

13 hex: Invalid default gateway
address

14 hex: Invalid primary name
server

15 hex: Invalid secondary name
server

16 hex: Invalid domain name

17 hex: Invalid host name

Stored

03D3 Link OFF error

00 hex

Not stored

Содержание NE1A-EDR01














































































































Результаты поиска

Содержание NE1A-EDR01

Отзывы:

Похожие инструкции для NE1A-EDR01

Бренды по названию

Популярные бренды

Omron NE1A-EDR01, Руководство по эксплуатации

Результаты поиска

Содержание NE1A-EDR01

Отзывы:

Похожие инструкции для NE1A-EDR01

Бренды по названию

Популярные бренды