Omron NE1A-EDR01 Скачать руководство пользователя страница 33

Страница: 33 / 109

Connecting to DeviceNet

Section 2-3

2-3

Connecting to DeviceNet

2-3-1

Setting the DeviceNet Node Address

Set the DeviceNet node address using the rotary switches (NODE ADR) on
the front of the ED Router.

Note

The node address is set to 63 at the factory.

Any node address in the setting range can be used as long as the same
address is not used by another node. If a value between 64 and 99 is set on
the rotary switches, the node address can be set using a software setting on
the Network Configurator.

IMPORTANT

• Turn OFF the power to the ED Router before setting the rotary switches.

• Do not change the rotary switches while the power is ON.

• A node address duplication error will occur if the same address is set for

more than one node. Communications will not start if this error occurs.

Note

• Use a small flat-blade screwdriver to set the rotary switches, being careful

not to scratch them.

• Refer to

2-3-3 DeviceNet Node Address and Baud Rate Software Settings

for software setting procedures.

2-3-2

Setting the DeviceNet Baud Rate

The DeviceNet baud rate is set using the DIP switch on the front of the ED
Router. The baud rate settings are shown in the following table:

Note

The baud rate is set to 125 kbit/s at the factory.

Note

Refer to

2-3-3 DeviceNet Node Address and Baud Rate Software Settings

for

software setting procedures.

Method

Two-digit decimal number

Range

0 to 63

Pin

Baud rate

OFF

125 kbit/s

OFF

250 kbit/s

OFF

500 kbit/s

OFF

Software setting

ON or
OFF

OFF

ON or
OFF

Automatic baud rate
detection

Содержание NE1A-EDR01














































































































Результаты поиска

Содержание NE1A-EDR01

Отзывы:

Похожие инструкции для NE1A-EDR01

Бренды по названию

Популярные бренды

Omron NE1A-EDR01, Руководство по эксплуатации

Результаты поиска

Содержание NE1A-EDR01

Отзывы:

Похожие инструкции для NE1A-EDR01

Бренды по названию

Популярные бренды