Omron NE1A-EDR01 Скачать руководство пользователя страница 46

Страница: 46 / 109

Troubleshooting

Section 3-2

3-2

Troubleshooting

3-2-1

ED Router Errors and Error Processing

Indicators/Display

Error

Cause

ED Router

operation

Error

code
(hex)

Countermeasures

NS D

NS E

7-seg-

ment

Hardware-related Errors

Lit red Not lit Not lit Not lit

or H3

System error ED Router fail-

ure

Operation stops.

None
or
0601

Replace the ED Router if the
problem recurs after restart-
ing.

Flash-
ing
red

---

Memory
access error

An error
occurred in
involatile mem-
ory in the Unit.

Operation stops.

0602

Flash-
ing
red

---

Not lit F4

Ethernet
communica-
tions control-
ler error

An Ethernet
communications
controller error
occurred.

Ethernet commu-
nications stop.

020F

Communications-related Error

---

Illegal mes-
sage dis-
carded.

The message
was discarded
due to illegal
packet commu-
nications.

Operation stops.

0118 Check the system communi-

cations status.

Ethernet Communications-related Errors

---

Link OFF
error

No link was
detected
between switch-
ing hubs.

Operation contin-
ues after error
recovery.

03D3 Check the Ethernet cable,

hub, etc.

---

Not lit E3

Server con-
nection error

An error
occurred
between the ED
Router and the
BOOTP server.

• There is no

response from
the BOOTP
server.

• The IP address

received from
the BOOTP
server is illegal.

Ethernet commu-
nications stop until
a legal IP address
can be received.

03C4 Check the BOOTP server.

---

Lit red F0

IP address
duplication
error

The ED Router
IP address is the
same as the IP
address set for
another device.

Ethernet commu-
nications stop.

0211 Check the IP address set-

tings and the network con-
nections.

Содержание NE1A-EDR01














































































































Результаты поиска

Содержание NE1A-EDR01

Отзывы:

Похожие инструкции для NE1A-EDR01

Бренды по названию

Популярные бренды

Omron NE1A-EDR01, Руководство по эксплуатации

Результаты поиска

Содержание NE1A-EDR01

Отзывы:

Похожие инструкции для NE1A-EDR01

Бренды по названию

Популярные бренды