background image

81

Appendix A

Specifications and Dimensions

General Specifications

DeviceNet Communications Specifications

EtherNet/IP Communications Specifications

Item

Specifications

DeviceNet supply voltage

11 to 25 VDC (Supplied from communications connector.)

Device supply voltage

20.4 to 26.4 VDC (24 VDC, 

15% to 10%)

Current 
consumption

DeviceNet

15 mA at 24 VDC

Internal logic circuits 230 mA at 24 VDC

Overvoltage category

II

EMC

Compliant with IEC 61131-2.

Vibration resistance

0.35 mm at 10 to 57 Hz, 50 m/s

2

 

at 57 to 150 Hz

Shock resistance

150 m/s

2

 for 11 ms

Mounting

DIN Track (TH35-7.5/TH35-15 according to IEC 60715)

Operating temperature

10 to 55

°

C

Humidity

10% to 95% (with no condensation)

Storage temperature

40 to 70

°

C

Degree of protection

IP20

Weight

220 g max.

Item

Specifications

Communications protocol

Conforms to DeviceNet and DeviceNet Safety.

Topology

Combination of multi-drop and T-branch connections (for trunk or branch lines)

Baud rate

125 kbps, 250 kbps, or 500 kbps

Communications media

Special 5-wire cable (2 signal lines, 2 power lines, 1 shield line)

Communications distances

Baud rate

Network length

Branch line length Total branch line length

500 kbps

100 m max. (100 m max.) 6 m max.

39 m max.

250 kbps

250 m max. (100 m max.) 6 m max.

78 m max.

125 kbps

500 m max. (100 m max.) 6 m max.

156 m max.

Values in parentheses are the lengths when using Thin Cables.

Communications power supply

11 to 25 VDC

Maximum number of nodes

63 nodes

Explicit message communications

Maximum message length: 511 bytes

Item

Specifications

Media access method

CSMA/CD

Modulation method

Baseband

Transmission path

Star type

Baud rate

10 Mbit/s (10Base-T)

100 Mbit/s (100Base-TX)

Transmission media

Shielded twisted-pair cable (STP), categories 5, 5e

Transmission distance

100 m (distance between hub and nodes)

Number of cascade connections 

No limit when a switching hub is used.

Содержание NE1A-EDR01














































































































Отзывы: