![background image](http://html1.mh-extra.com/html/omron/f3sg-pg-series/f3sg-pg-series_user-manual_741299417.webp)
387
F3SG-SR/PG
User’s Manual
Chapter
6
Wiring Exa
m
p
le
s
(f
or F3
SG-SR/PG)
Input/Output Circuit and Applications
E
6-2-1-4. Manual Reset Mode with EDM
[Wiring Example (F3SG-SR and F3SG-PGA-A/-L*6)]
When a functional earth is necessary, wire an earth cable according to the example in
6-2-1-1. Auto Reset Mode with Optical
Synchronization and EDM Unused
. Also refer to
5-4-4. Functional Earth Connection
F3SG-SRA
F3SG-PGA-A/-L
F3SG-SRB
F3SG-PGA-C
*6
KM1
KM2
M
Timing chart
24
V
DC
W
iring for
N
P
N
*1
*3
24
V
DC
KM1
KM2
S2
S1
KM1
KM2
S1: Test s
w
itch
S2: Locko
u
t/interlock reset s
w
itch
KM1, KM2: Safety relay
w
ith forci
b
ly g
u
ided contacts (G7SA) or magnetic contactor
M: Motor
Beam state: Un
b
locked
Blocked
Test s
w
itch (S1)
Reset s
w
itch (S2)
OSSD
Recei
v
er
Emitter
OSSD 1 (Black)
OSSD 2 (
W
hite)
24
V
/0
V
(Bro
w
n)
OPERATI
N
G RA
N
GE
SELECT I
N
PUT (Yello
w
) *2
TEST (Black)
N
ot
u
sed (
W
hite)
24
V
/0
V
(Bro
w
n)
0
V
/24
V
(Bl
u
e)
0
V
/24
V
(Bl
u
e)
AUX (Red)
MUTE B (Pink)
MUTE A (Gray)
RESET/EDM
(Y
ello
w
)
F39-JGR3K-L
F39-JG
A-L
F39-JGR3K-D
F39-JG
A-D
*1. Reverse the polarity of the power supply when using in the NPN system.
*2. Connect the line to 0 VDC if Operating Range Selection is used in Short Mode
on F3SG-SR and F3SG-PGA-L.
*3. This is the case for a PELV circuit.
*4. Set the function with the DIP Switches on the Intelligent Tap or the SD Manager
3, restore the settings to the F3SG-SR/PG, and perform wiring according to the
wiring diagram.
*5. This wiring example shows light emission stop when connected to 24 VDC with
PNP setting, and light emission stop when connected to 0 VDC with NPN
setting. If TEST switch is not needed, refer to
.
*6. To use F3SG-PGA-C, wire the receiver side of the emitter/receiver of F3SG-
PGA-C as shown in the above figure. Wiring of the emitter side is not needed.
*7. F3SG-PGA-C does not support the External Test function.
: Indicates a switch position.
Function
Setting
DIP switch
SD Manager 3
EDM *4
EDM Enabled
[External device monitoring] : Enable
Interlock *4
Manual Reset
[Start interlock] : Enable
[Restart interlock] : Enable
Operating Range Selection
Long : Open the OPERATING RANGE SELECT INPUT line of the emitter or connect the line to 24 VDC.
Non-Muting system
Perform wiring according to the wiring diagram.
N/A
[Muting] : Disable *4
External Test used *7
Connect the TEST line of the emitter to 24V/0V of the emitter via a test switch (NO contact). *5
N/A
[External test signal inversion] : Disable
Optical Synchronization
Perform wiring according to the wiring diagram.
㻟
㻻㻺
㻠
㻻㻺
㻡
㻻㻺
Intelligent Tap
Needed
Содержание F3SG-PG Series
