![background image](http://html1.mh-extra.com/html/omron/cqm1h-08-2005/cqm1h-08-2005_operation-manual_742096280.webp)
260
2-9
Command Tables
I/O Allocation Commands
C
Item To Be Set
Item To Be Monitored
Output word
Loop number: 1 to 4
Value
Item to be set
Value
Item to be monitored
0
Set point
0
Set point
1
Proportional band (for advanced PID)
1
Proportional band (for advanced PID)
2
Integral time (for advanced PID)
2
Integral time (for advanced PID)
3
Derivative time (for advanced PID)
3
Derivative time (for advanced PID)
4
Hysteresis (for ON/OFF control)
4
Hysteresis (for ON/OFF control)
5
Control cycle (for advanced PID or manual
control)
5
Control cycle (for advanced PID or manual
control)
6
Input shift value
6
Input shift value
7
No item set
7
Process value
8
Manual manipulated variable
8
Manipulated variable
9
Do not set.
9
Status
A
Heater burnout alarm setting (only for models with
heater burnout alarms)
A
Heater burnout alarm setting (only for models with
heater burnout alarms)
B
Do not set.
B
Heater current (only for models with heater
burnout alarms)
Operation Control Commands
Command
Operation
Validity
CCC
j
(
j
= 1 to 4 or A)
STOP
Always (STOP/RUN in Auto
CCD
j
(
j
= 1 to 4 or A)
RUN
Mode)
CDC
j
(
j
= 1 to 4 or A)
Manual Mode
Not valid during autotuning.
CDD
j
(
j
= 1 to 4 or A)
Auto Mode
CFC
j
(
j
= 1 to 4 or A)
Autotuning
PID control (Not valid during
Manual Mode or STOP.)
CFD
j
(
j
= 1 to 4 or A)
Cancel autotuning
PID control
CEEA
Writing set point to
EEPROM
Always
Error Responses
Error
response
Meaning
Remarks
EEEE
Watchdog timer error
Turn the power supply OFF and then back
E100
RAM read/write error
ON. If the error persists, replace the Unit.
E120
EEPROM error
EE00
Parameter change
during autotuning
Set parameter after autotuning has been
completed.
EE01
Setting range error
Setting is out of range.
E400
Sensor error
Input error, sensor wire break, sensor short,
etc.
E500
CT input error
Input of 55.0 A or more.
E900
Timeout error (for
IOTC(––) instruction)
Response time of 200 ms or higher for macro
instruction
Command Tables
Section 2-9
Содержание CQM1H - 08-2005
