Omicron CMC 310 Скачать руководство пользователя

Страница: 14 / 44

CMC 310 User Manual

OMICRON

3.3

Back panel connections

Rear view of the

CMC 310

with the NET-2 interface board:

3.3.1

USB ports

USB

port type

is used to insert USB peripherals such as wireless USB adapters. Only

OMICRON-supplied wireless USB adapters are supported.

USB

port type

is used to connect the

CMC 310

to your computer.

► To improve electromagnetic compatibility, use the OMICRON-supplied cable.

For the technical data of the

USB

port see section 4.6 "Technical data of the communication ports" on

page 34.

Power supply, fuse T12.5 AH

Ethernet ports

ETH1

and

ETH2

1. The hardware for

LL out 1–6

and

ETH2

exists but is not used in the

CMC 310

Fans for power supply

button

External interface

ext. Interf.

Interfaces

LL out 1– 6

Status LEDs A and B

Grounding socket

Used to connect the CMC test set to protective earth
using a grounding cable if grounding via the power
outlet is insufficient (see section "Grounding" in the
Safe use of CMC test sets manual).

Associate

button

USB

ports type

and

Fans for current and voltage outputs

Содержание CMC 310













































Результаты поиска

Содержание CMC 310

Отзывы:

Похожие инструкции для CMC 310

Бренды по названию

Популярные бренды

Omicron CMC 310, Руководство пользователя

Результаты поиска

Содержание CMC 310

Отзывы:

Похожие инструкции для CMC 310

Бренды по названию

Популярные бренды