Omicron CMC 310 Скачать руководство пользователя

Страница: 7 / 44

OMICRON

Safety

Rules for use

► Before operation, visually check for damages and make sure that the device and its accessories are

in a technically sound condition.

► Use

CMC

test sets only in accordance with the safety regulations for the specific job site and

application.

► Follow the instructions provided in the documentation.
► Testing with

CMC

test sets shall only be carried out by authorized and qualified personnel. Before

starting to work, clearly establish the responsibilities of all personnel involved.

► Personnel operating

CMC

test sets must be familiar with all necessary personal safety equipment.

► Testing with

CMC

test sets must comply with all on-site procedures and methods for personal safety.

► Personnel receiving training, instruction, direction, or education on

CMC

test sets should remain

under the constant supervision of an experienced operator while working with the equipment.

► Keep this document available on site where the

CMC

test sets are used.

Safe operation procedures

► Ensure proper grounding of the device and of the equipment under test.
► Use a power supply with protective earth.
► The power cable must be rated for the nominal voltage and current specified in section 4.2 "Main

power supply" on page 19. We recommend to use the cable supplied with the test sets.

► Do not block the access to safety-relevant test set components like the power switch or the power

cable.

► Operate

CMC

test sets only under the environmental conditions specified in section

4.7 "Environmental conditions" on page 35. Especially avoid a condensing environment.

► Do not operate

CMC

test sets when explosive gas or vapors are present.

► When setting up

CMC

test sets, make sure that the ventilation holes on the rear of the device remain

unobstructed.

► The fuse (→ section 2.5 "Changing the power fuse" on page 8) is the only serviceable part in

CMC

test sets. Do not open

CMC

test sets or carry out any modifications, extensions, or adaptations.

► If

CMC

test sets seem to be functioning improperly, please contact OMICRON Support.

► Falling adapters or cables are a hazard. Test leads wired to tall test objects must be secured

mechanically.

► Do not connect any of the front panel outputs of

VOLTAGE OUTPUT

CURRENT OUTPUT

protective earth. The

sockets, however, may be connected to protective earth.

► Do not connect high inductive loads to

CMC

test sets.

► Observe the wiring instructions and safety precautions given in the Safe use of CMC test sets

manual.

Содержание CMC 310













































Результаты поиска

Содержание CMC 310

Отзывы:

Похожие инструкции для CMC 310

Бренды по названию

Популярные бренды

Omicron CMC 310, Руководство пользователя

Результаты поиска

Содержание CMC 310

Отзывы:

Похожие инструкции для CMC 310

Бренды по названию

Популярные бренды