Omicron CMC 310 Скачать руководство пользователя страница 6

Страница: 6 / 44

CMC 310 User Manual

OMICRON

Safety

2.1

Designated use

The

CMC 310

is a test set controlled by the

CMControl P

software for the testing of protection relays,

energy meters, SCADA systems and devices.
► Do not use

CMC

test sets in any other way than described in this document or in working

environments that exceed the specifications given in section 4 "Technical data". Improper use may
result in damage to persons or property.

2.2

Safety symbols used

In this document, the following symbols indicate safety instructions for avoiding hazards.

2.3

Safety instructions

► Before operating a

CMC

test set, carefully read the following safety instructions.

► Only operate (or even turn on) the

CMC

test set after you have read this manual including section

4 "Technical data" on page 18, and fully understood the instructions. We also recommend to read all
other relevant documentation for your test set and control software.

For your safety

Only trained personnel may operate

CMC

test sets. Any maloperation can result in damage to property

or persons.

You can remotely activate

CMC

test set outputs if the

CMC

is turned on and connected to a suitable

control software or control device (via network, wireless or USB).
► Observe all necessary safety measures given below.

All 4 mm safety sockets on the front panel can carry signals at dangerous levels and can conduct
dangerous voltages.

WARNING

Death or severe injury can occur if the appropriate safety instructions are not
observed.

NOTICE

Equipment damage or loss of data possible.

Содержание CMC 310













































Результаты поиска

Содержание CMC 310

Отзывы:

Бренды по названию

Популярные бренды

Omicron CMC 310, Руководство пользователя

Результаты поиска

Содержание CMC 310

Отзывы:

Бренды по названию

Популярные бренды