Olympic Medical BILI-LITE 33 Скачать руководство пользователя страница 35 | Manualshive

Страница: 35 / 56

Olympic Medical BILI-LITE 33 Скачать руководство пользователя страница 35

OLYMPIC BILI-LITE

Model 33/34 Instruction Manual

6-5

Repair Procedures

Removing the Light Hood

The light hood must be removed before accessing the wiring.

To remove the light hood:

1

Turn the

POWER

switch to the

OFF (O)

position, and then unplug the power

cord from the electrical outlet.

2

Remove the power cord from the clamp.

3

Loosen and remove the three black knobs on the support arm (see Figure 6.2).

(If you have a tilt assembly installed, remove the three acorn nuts.)

Figure 6.2

Loosen the knobs on top of the light hood

4

Gently lower the light hood from the support arm.

To reattach the light hood:

1

Hold the light hood up to the support arm with the holes aligned.

2

Insert and secure the three knobs on the support arm.

3

Insert the power cord into the clamp.

4

Perform the test procedure (see page 2-8).

CAUTION

The light hood is heavy. Installing or removing the light hood requires two people.

Tighten the support post height adjustment knob firmly before attempting to remove the
light hood.

Knobs (x3)

«
...
33
34
35
36
37
...
»

Содержание BILI-LITE 33

























































Отзывы:

Нет отзывов