Olympic Medical BILI-LITE 33 Скачать руководство пользователя страница 33 | Manualshive

Страница: 33 / 56

Olympic Medical BILI-LITE 33 Скачать руководство пользователя страница 33

OLYMPIC BILI-LITE

Model 33/34 Instruction Manual

6-3

Repair Procedures

Replacing the Power Switch

If the power switch malfunctions, it may need to be replaced.

Required Items:

Replacement power switch (part no. 200001)

Medium-size flat-blade screwdriver

Medium-size Phillips-head screwdriver

5/16-in. nut driver

3/8-in. nut driver

To remove the power switch:

1

Press the power switch to the

OFF

(O) position, then unplug the power cord.

2

Remove the safety shield: First, remove the two retaining screws and washers.

Next, slide the safety shield out.

3

Rotate each bulb out of its socket; set the bulbs aside in a secure place.

4

Remove the light hood from the support post (see page 6-5).

5

Remove the fan shroud: Loosen and remove the three Phillips-head screws

and washers.

6

Remove the safety shield bracket: Loosen and remove the two acorn nuts and

two Phillips-head screws and washers.

7

Remove the reflector:

a

Remove the four nuts and washers securing the reflector to the light hood

(see Figure 6.1).

Figure 6.1

Removing the reflector

CAUTION

The light hood is heavy. Installing or removing the light hood requires two people.

Tighten the support post height adjustment knob firmly before attempting to remove the
light hood.

Nuts and washers (x4)

Reflector

Light hood

NOTE: Not pictured:

Safety shield bracket with
acorn nuts (x2), Phillips-head
screws (x2) washers (x4

Fan shield with screws (x3)
and washers (x3)

«
...
31
32
33
34
35
...
»

Содержание BILI-LITE 33

























































Отзывы:

Нет отзывов