Olympic Medical BILI-LITE 33 Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 56

Olympic Medical BILI-LITE 33 Скачать руководство пользователя страница 18

2-4

OLYMPIC BILI-LITE

Model 33/34 Instruction Manual

Attaching the Tilt Hood Assembly

Attaching the Tilt Hood Assembly

A tilt assembly can also be added to a Model 33/34. To order a tilt assembly, see

Ordering Information

Required Items:

Tilt hood assembly, which includes adhesive

Medium-size adjustable wrench

Phillips-head screwdriver

Nutdriver, slim-profile preferred

To attach the tilt hood assembly:

1

If adding a tilt assembly while assembling your new Model 33/34,

perform

steps 2–6 starting on page 2-1, then perform the hood tilt assembly steps below.
– or –

If adding the tilt hood assembly to your assembled Model 33/34,

press the

power switch to the Off (O) position, unplug the power cord, perform the

steps 6–9 starting on page 2-1, then perform the hood tilt assembly steps below.

2

Place the tilt hood bar, with the large holes facing down and the side holes

toward the front of the light hood, on top of the light hood (see Figure 2.2).

Figure 2.2

Placing the tilt hood bar

3

Insert the three hood bolts up, through the light hood, through the bar and secure

with lock nuts (see Figure 2.3). Affix fastener caps over the lock nuts using the

small tube of Loctite

®

401 supplied in this kit.

NOTE

#

The adjustment screw assembly and the pivot assembly are shipped with their mounting
fasteners loosely assembled. They may be disassembled as required to attach them during
the following steps.

NOTE

#

If you do not have a slim-profile nutdriver or socket, you might not be able to reach inside
the square tubing to install the lock nuts. You may instead install these brackets with the
mounting screws placed inside the support post arm and the lock nut on top of the bar. After
assembly is complete the five extra fastener caps supplied with this kit may be affixed over
the lock nuts using the small tube of Loctite

®

401 supplied with this kit

Light hood

FRONT

Tilt hood bar

Lock nuts, securing hood bolts (x3)

Power cord

BACK of light hood

Side holes (x2) at

front of light hood

«
...
16
17
18
19
20
...
»

Содержание BILI-LITE 33

























































Отзывы:

Нет отзывов