OLT PEN99 Скачать руководство пользователя

Страница: 35 / 39

Outdoor Living Today www.outdoorlivingtoday.com [email protected]

Page 35

Attach Black Tee
Hinges with 1”
Black screws.

87.

Attach Door Hinges to both

Left

and

Right Side Double French Doors

. Position Hinges

equally on door as shown above and attach with

1” Black Screws.

Note:

Pre-drill holes for hinges

to prevent splitting.

88.

Position and secure the Double Doors. Starting with

Left Side Door

, position so there is a

1/4” gap on bottom and approximately 1/4” on the side. Use the extra piece of

Filler Shingle

shim door in place at the bottom and side. Using

2” Black Screws

, secure hinges to Door Trim.

Hint:

Do not attach all the 2” Black Screws until both doors are positioned correctly. Use Screw

Driver to tighten screws completely.

1/4” gap

Note:

illustration of Hinge may not be

accurate. The # of screw holes in the
hinge may vary from three to four
depending on model.

89.

Position

Right Side Door

as per

Step 88

and secure with

2” Black Screws.

When satisfied

with door positioning, complete all

2” Black Screws. Note:

Do not over tighten hinge screws when

using screw gun.

Optional:

Using a hand tube of clear silicon caulking, apply caulking across bot-

tom of window frame and up both edges vertically for 1”. This will decrease the chances of water
penetration at bottom of window.

Содержание PEN99








































Результаты поиска

Содержание PEN99

Отзывы:

Похожие инструкции для PEN99

Бренды по названию

Популярные бренды

OLT PEN99, Инструкция по сборке

Результаты поиска

Содержание PEN99

Отзывы:

Похожие инструкции для PEN99

Бренды по названию

Популярные бренды