OLT PEN99 Скачать руководство пользователя

Страница: 34 / 39

Outdoor Living Today www.outdoorlivingtoday.com [email protected]

Page 34

85.

Locate both

Right and Left Doors.

If you choose to paint or stain your shed you can remove the

window from the door. Remove screw from top and bottom of window frame to detach window. Once
treated you can return the window into the door and replace the screw.

Important:

When reinstalling

the window, ensure the Mullion is facing outside your shed.

Remove screws
in frame

Window mullion facing
outside of shed.

86.

Locate

Door Trim Bundle.

Align Trim pieces 1/4” from edge of window framing. Fasten trim

pieces to door with

1” Finishing Nails.

Use

3 - 1” Finishing Nails

for the short pieces and

5 - 1”

Finishing Nails

per long piece. When nailing, alternate which edge is fastened as illustrated above.

Trim recessed 1/4”
on each side
from window frame

Содержание PEN99








































Результаты поиска

Содержание PEN99

Отзывы:

Похожие инструкции для PEN99

Бренды по названию

Популярные бренды

OLT PEN99, Инструкция по сборке

Результаты поиска

Содержание PEN99

Отзывы:

Похожие инструкции для PEN99

Бренды по названию

Популярные бренды