UNICO TWIN
FRANÇAIS
FR - 19
3 - branchements frigorifiques
ouvrir la protection latérale d’accès aux raccords.
• Ne pas exécuter les branchements en utilisant des tuyaux hydrauliques
normaux qui pourraient contenir à l’intérieur des résidus de copeaux, de la
saleté ou de l’eau, et qui peuvent endommager les composants des unités et
compromettre le correct fonctionnement des appareillages.
• Utiliser exclusivement des tuyaux en cuivre spécifiques pour réfrigération qui
sont fournis nettoyés et fermés à leurs extrémités.
Après avoir effectué les coupes, boucher immédiatement les extrémités du rouleau et du bout
coupé.
Utilisez uniquement des tuyaux dont les diamètres correspondent aux dimensions décrites dans
le tableau des caractéristiques techniques.
On peut utiliser des tuyaux en cuivre pour réfrigération déjà préisolés.
si l’on n’utilise pas de tuyauterie préisolée, introduire les tuyaux dans l’isolant qui doit avoir les caractéris-
tiques suivantes:
- matériau: polyuréthanne expansé à cellule fermées
- coefficient de transmission maxi:0,45 W/ (Kxm2)
- épaisseur minimale : 6 mm (pour liquide) et 9 mm (pour gaz).
- Repérer le parcours des tuyauteries de façon à réduire le plus possible la longueur et les coudes des
tuyaux et ainsi obtenir le maximum de rendement de l’installation.
la longueur maximale des tuyauteries doit être de 10 m dans chaque sens.
Différence de niveau maximum entre les deux unités +/- 5 m.
- Fixer au mur une gaine de câbles (si possible avec cloison interne) de dimensions adéquates où l’on
fera passer successivement les tuyaux et les câbles électriques.
- Couper les morceaux de tuyau en excédant d’environ 3-4 cm sur la longueur.
Effectuer la coupe exclusivement à l’aide d’un coupe-tube à mollettes resserrant
par petits intervalles pour ne pas écraser le tuyau.
NE JAMAIS UTILISER UNE SCIE NORMALE,
les copeaux pourraient entrer dans le tuyau et par la suite entrer en circulation
dans l’installation, endommageant sérieusement les composants.
- Raccorder soigneusement avec du ruban adhésif les éventuelles jonctions de la gaine.
- Enfiler l’écrou de blocage sur le tuyau, avant d’évaser l’extrémité.
- Evaser les extrémités des tuyaux, en utilisant l’outil prévu à cet effet, de manière impeccable, sans
cassures, fentes ou clivages.
- Lubrifier le filet du raccord UNIQUEMENT avec de l’huile pour réfrigérant.
- Visser manuellement puis, avec une clé fixe, l’écrou du tuyau sur le filetage du raccord.
Serrer à fond en utilisant une clé à fourches pour maintenir bloquée la partie filetée du raccord, afin
d’éviter des déformations, et une clé dynamométrique sur l’écrou réglée aux valeurs suivantes
selon les dimensions des tuyaux:i:
- 14-18 nxm (1,4-1,8 kgxm) pour un diamètre des tuyaux ø 6-6,4 mm
- 33-40 nxm (3,3-4,0 kgxm) pour un diamètre des tuyaux ø 9,5-10 mm
- 50-60 nxm (5,0-6,0 kgxm) pour un diamètre des tuyaux ø 12-12,7 mm.
Содержание Unico Twin
