UNICO TWIN
ENGLISH
EN - 27
• In this mode, both room temperature and fan speed settings are ignored, which correspond to minimum.
• To activate this mode, press several times key
T4
on the remote control until when symbol
U4
and the
automatic ventilation symbol
U1
appear on its display.
• In this operating mode it is normal for the air conditioner to function intermittently.
5.4.5 - OPERATION IN “VENTILATION” MODE ONLY
• When used in this mode the air conditioner does not perform any action with regard to temperature and
air humidity in the room.
• To activate this mode, press several times key
T4
on the remote control until when the automatic ventilation
symbol
U1
appears on its display.
5.4.6 - OPERATION IN “HEATING” MODE ONLY
• Using this mode, the appliance heats the room.
• To activate this mode, press several times key
T4
on the remote control until when symbol
U2
appears
on its display
.
• In this run mode, the required temperature and fan speed can be set.
after three minutes (maximum time)
from the activation of this mode of operation, the appliance starts supplying heat.
The activation of the compressor is indicated by the illumination of the corresponding LED B (fig. C)
located on the console.
The air conditioner has to defrost its battery periodically.
During this operation the air conditioner does not heat the room, though its internal
parts remain on except for the room air fan. when the outdoor temperature is very
low, there may be a slight delay for passage from the minimum to the medium or
maximum speed from when the command is sent to the machine with the remote
control.
Like delays might occur on activating the swinging function of the mobile baffle.
5.4.7 - CHECKING AIRFLOW DIRECTION
• Press key
T9
on the remote control to activate/deactivate the continuous oscillation of the moving air
outlet deflector (fig.A - ref. 1).
• When continuous oscillation is active, an additional press of the key allows to lock the deflector so as to
obtain the desired vertical direction for the air flow.
The moving deflector position must never be forced manually.
5.4.8 - CHECKING FAN SPEED
• The fan speed check occurs through key
T5
(on the remote control).
• Pressing several times this key will cause speed to change according to the following sequence:
low > medium > High > automatic.
• The higher the speed setting, the greater the output of the air conditioner but also the louder its operation.
• By setting the
Automatic
mode, the onboard microprocessor adjusts the automatic speed. the higher
the difference between the room temperature detected and the temperature set, the higher the speed.
• As the room temperature nears the setting, fan speed is reduced automatically.
• In dehumidification mode, it is not possible to control the speed as the appliance can only operate exclu
-
sively at low speed.
Содержание Unico Twin
