UNICO TWIN
IT - 19
IT
ALIANO
3 - COLLEGAMENTI FRIGORIFERI
Aprire la protezione laterale di accesso agli attacchi.
• Non eseguire i collegamenti utilizzando normali tubazioni idrauliche che al loro
interno potrebbero contenere residui di trucioli, sporcizia o acqua, e che possono
danneggiare i componenti delle unità e pregiudicare il corretto funzionamento
delle apparecchiature.
• Usare esclusivamente tubazioni in rame specifici per refrigerazione che vengono
forniti puliti e sigillati alle estremità.
Dopo aver eseguito i tagli sigillare immediatamente le estremità del rotolo e dello spezzone tagliato.
Utilizzare esclusivamente tubi con diametri che rispecchiano le dimensioni descritte nella tabella
dei dati tecnici.
É possibile utilizzare tubi in rame per refrigerazione già preisolati.
Nel caso non si utilizzino tubazioni preisolate, inserire i tubi nell’isolante che deve avere le seguenti caratte
-
ristiche:
- materiale: poliuretano espanso a celle chiuse
- coefficiente di trasmissione max: 0,45 W/ (Kxm2)
- spessore minimo: 6 mm (per liquido) e 9 mm (per gas).
- Individuare il percorso delle tubazioni in modo da ridurre il più possibile la lunghezza e le curve dei tubi
per ottenere il massimo rendimento dell’impianto.
La lunghezza massima delle tubazioni deve essere di 10 m per ciascun senso.
Il dislivello massimo tra le due unità deve essere di circa 5 m.
- Fissare al muro una canalina passacavi (possibilmente con separatore interno) di opportune dimensioni
in cui far passare successivamente le tubazioni e i cavi elettrici.
- Tagliare i tratti di tubazione abbondando di circa 3-4 cm sulla lunghezza.
Effettuare il taglio esclusivamente con un tagliatubi a rotella stringendo a piccoli
intervalli per non schiacciare il tubo.
NON UTILIZZARE MAI UN NORMALE SEGHETTO, i trucioli potrebbero entrare
nel tubo e successivamente in circolo nell’impianto danneggiando seriamente
i componenti.
- Unire accuratamente con nastro adesivo le eventuali giunzioni della guaina.
- Infilare nel tubo, prima di eseguire la cartellatura, il dado di fissaggio.
- Eseguire la cartellatura sulle estremità dei tubi, utilizzando l’apposito utensile, in modo impeccabile,
senza rotture, incrinature o sfaldature.
- Lubrificare il filetto dell’attacco con SOLO olio per refrigerante.
- Avvitare manualmente e poi con una chiave fissa il dado del tubo sulla filettatura dell’attacco.
Avvitare definitivamente utilizzando una chiave fissa per tenere ferma la parte filettata dell’attacco,
per evitarne deformazioni, e una chiave dinanometrica, sul dado tarata con i seguenti valori in base
alle dimensioni dei tubi:
- 14-18 Nxm (1,4-1,8 kgxm) per diametro tubi ø 6-6,4 mm
- 33-40 Nxm (3,3-4,0 kgxm) per diametro tubi ø 9,5-10 mm
- 50-60 Nxm (5,0-6,0 kgxm) per diametro tubi ø 12-12,7 mm.
Содержание Unico Twin
