IT - 14
IT
ALIANO
2.3.1.3 - MONTAGGIO DEI CONDOTTI DELL’ARIA E DELLE GRIGLIE ESTERNE
• Dopo aver eseguito i fori (con la carotatrice), inserire negli stessi il foglio in plastica (G) in dotazione con
il climatizzatore (fig. 11).
Il foglio (G) è predisposto per i fori da 202 mm; per i fori da 162 mm occorre tagliare dal foglio un lembo
di 130 mm sul lato lungo (fig. 11).
La lunghezza dei fogli deve essere di 65 mm inferiore a quella della parete.
• Arrotolare il foglio (G) e introdurlo nel foro, prestando attenzione alla linea di giunzione
che deve sempre
essere posizionata verso l’alto
(fig.12)
.
Per tagliare il tubo (G) è sufficiente utilizzare un normale taglierino (fig12).
Per il posizionamento delle griglie esterne operare come segue:
a
. Applicare sulle flange a muro (F) la guarnizione (D) facendole coincidere con il bordo esterno della
flangia stessa come indicato in figura 13.
b
. Fissare le due flange con 2 tasselli diametro 6 mm con i due fori di fissaggio in posizione orizzontale
(figure 14 - 15 - 16).
c
. Infilare l’occhiello piccolo, con gambo lungo, della molla sul perno del tappo (su ambedue i componenti)
(fig.17).
d
. Infilare i due tappi (con molla) dalla parte anteriore della griglia esterna sulle due sedi della stessa,
tirando fino allo scatto (fig.18) quindi attaccare le due catenelle all’occhiello grande della molla.
e
. Impugnare con una mano le due catenelle collegate alla griglia;
f
. Ripiegare su se stesse le griglie esterne impugnandole con la mano libera nella parte di ripiegatura e
introducendo le dita all’interno delle singole alette (fig.19).
g
. Introdurre il braccio nel tubo sino a far sporgere completamente la griglia all’esterno.
h
. Lasciare riaprire la griglia facendo attenzione a trattenere le dita all’interno delle alette.
i
. Ruotare la griglia sino a quando le alette sono ben orizzontali e con l’inclinazione rivolta verso il basso.
l
. Tirare la catenella tensionando la molla, quindi agganciare l’anello della catenella al perno della flangia
interna passaggio tubi (fig. 20).
m
. Tagliare con un tronchese le maglie delle catenelle in eccesso.
Usare esclusivamente le griglie in dotazione (E), oppure delle griglie che mantengano le medesime
caratteristiche.
2.3.1.4 - PREDISPOSIZIONE FORI SULLA MACCHINA
L’unità esce dalla fabbrica predisposta per l’accoppiamento con tubi da 162 mm; per ottenere le migliori
prestazioni e la maggiore silenziosità occorre utilizzare i fori da 202 mm e l’unità deve essere configurata
seguendo le indicazioni riportate:
• Con un taglierino incidere sul preforo della copertura posteriore e togliere la parte di copertura (fig. 21)
in modo da creare il foro di passaggio aria con il diametro di 202 mm.
2.3.1.5 - POSIZIONAMENTO DELL’APPARECCHIO
• Per fissare la staffa eseguire i fori alla parete nella posizione prescelta e fissarla con i tasselli in dotazione
(fig.22).
• Posizionare correttamente la staffa mediante una bolla e infine serrare definitivamente la piastra con le
relative viti (fig.22).
Operare come segue:
a
. Sollevare il climatizzatore prendendolo ai lati della base inferiore e agganciarlo alla piastra (L1) (fig. 24).
Per agevolare l’operazione di aggancio inclinare leggermente la parte bassa dell’apparecchio verso se
stessi.
Содержание Unico Twin
