background image

21

·

CAREFULLY FOLLOW THE INSTRUCTIONS BELOW TO ENSURE THE IDEAL OPERATION OF

THE AIR  CONDITIONER.

·

HANDLE THE UNIT WITH CARE AND NEVER TURN THE AIR CONDITIONER UPSIDE-

DOWN DURING INSTALLATION.

·

NEVER REMOVE THE UNIT'S REAR PANEL FOR ANY REASON IN ORDER TO

AVOID COMPROMISING OPERATION.

·

AT THE END OF INSTALLATION, EXPLAIN THE UNIT'S OPERATION TO THE CLIENT USING

THE OPERATION AND MAINTENANCE MANUAL.

·

GIVE THE OPERATION AND MAINTENANCE MANUAL TO THE CUSTOMER.

The position of the  air conditioner is extremely important for both correct operation and the comfort of the room or area.

Choose the unit's  position together with the customer while taking into consideration the following points:

A

. The air must be distributed as evenly as possible throughout the room, taking into consideration that warm air tends to rise

and cool air tends to fall.

B.

The flow of air emitted by the unit must never strike the room's occupants directly.

C.

Internal units must never be obstructed by furniture or curtains, etc.;

The RDW 9RN Model Air conditioner

Installation Manual

1. SELECTING THE INSTALLATION POSITION

Summary of Contents for RDW 9RN





















Reviews: