Okolab UNO-T Скачать руководство пользователя страница 18

Страница: 18 / 73

Gas Connection

7.3.1

Gas connection for UNO-T-H-PREMIXED

UNO-T-H-PREMIXED is suitable or applications with premixed gas supply. Follow the steps below for a

correct installation:

Install the GF-REGULATOR between the premixed gas supply and the Humidifier (see Figure 13). Use

TUBE-A to connect the premixed gas supply to the push to fit input connector for a 6 mm O.D. rigid tube

of the GF-REGULATOR (see Figure 13).

During this operation make sure that both the premixed gas tank and the GF-REGULATOR are closed.

Be careful to follow the direction of the arrow on the rear of the GF-REGULATOR for the correct gas in-out

orientation (see Figure 12).

Figure 12. GF-REGULATOR - front and rear view (a - b).

The premixed gas tank must be equipped with a pressure regulator to decrease the pressure from
the pressure tank to 4 barg (58 psig).
Do not exceed 10 barg (145 psig) for GF-REGULATOR inlet gas pressure. This may damage the GF-
REGULATOR.

Connect the blue rigid end of TUBE-C to the output connector of GF-REGULATOR. Connect the silicon end

of TUBE-C to the Gas Inlet gas connector of the Humidifier (see Figure 13). TUBE-C is equipped with a

PTFE filter in the middle. Make sure to install the TUBE-C in the direction of the gas flow indicated by the

labels on both ends of TUBE-C and on both sides of the PTFE filter.

Tip

►

Replace the PTFE filter each 2-3 months of continuous operation or if you see water in the inner part

of the filter.

Do not use TUBE-C without the PTFE filter.

Содержание UNO-T










































































Результаты поиска

Содержание UNO-T

Отзывы:

Похожие инструкции для UNO-T

Бренды по названию

Популярные бренды

Okolab UNO-T, Руководство пользователя

Результаты поиска

Содержание UNO-T

Отзывы:

Похожие инструкции для UNO-T

Бренды по названию

Популярные бренды