Okolab UNO-T Скачать руководство пользователя страница 22

Страница: 22 / 73

Connect the blue rigid end of TUBE-C to the

“Air + CO2 OUT”

push to fit connector of on the rear panel of

2GF-MIXER. Connect the silicon end of TUBE-C to the Gas Inlet gas connector of the Humidifier (see Figure

18). TUBE-C is equipped with a PTFE filter in the middle. Make sure to install the TUBE-C in the direction

of the gas flow indicated by the labels on both ends of TUBE-C and on both sides of the PTFE filter.

Tip

►

Replace the PTFE filter of TUBE-B and TUBE-C each 2-3 months of continuous operation or if you see

water in the inner part of the filter.

Do not use TUBE-B or TUBE-C without the PTFE filter.

TUBE-C

ION

Humidifier

2GF-MIXER

Figure 18. UNO-T-H-CO2

–

TUBE-C connection.

Tip

►

Make sure to push the tubes all the way into the connectors thus avoiding any gas leak.

7.3.2.1

How to use 2GF-MIXER

The 2GF-MIXER generates a CO2/air mixture with an adjustable CO2 concentration in the range 0-15%.

The desired CO2 concentration is obtained by regulating the air and CO2 flow rate, in the range 0.1

–

1 l/min and

0.013

–

0.13 l/min respectively, using the two floating ball flow meters.

Do not use the 2GF-MIXER as closing-opening valves. Once regulated the flow rate (at inlet CO2
pressure of 1barg), use the 2GF-MIXER carefully only for fine regulations.

Follow the instructions below:

Open the gas valves about 15 minutes before inserting the sample in the H301 Okolab incubating chamber.

Table 2 reports the CO2 and air flow rates to be set in order to obtain a concentration of CO2 equal to 5%

at the 2GF-MIXER outlet.

“

Target Gas Percentage

”

indicates the desired outlet gas percentage that the

operator wants during the experiment.

“

Gas flow rate

”

, in litre per minute [l/min], are the values of gas

flow rate to be set on the graduated scale on the front panel of 2GF-MIXER.

“Total” column reports the

measured the total gas flow rate at the 2GF-MIXER outlet.

Содержание UNO-T










































































Результаты поиска

Содержание UNO-T

Отзывы:

Похожие инструкции для UNO-T

Бренды по названию

Популярные бренды

Okolab UNO-T, Руководство пользователя

Результаты поиска

Содержание UNO-T

Отзывы:

Похожие инструкции для UNO-T

Бренды по названию

Популярные бренды