Okolab UNO-T Скачать руководство пользователя страница 60

Страница: 60 / 73

•

TOP LED Settings.

The TOP LED settings allows you to establish when the TOP LED should be illuminated:

if you select

Never

, the Top LED will never illuminate, if you select

On Alarm

, the TOP LED will illuminate

only when UNO-CONTROLLER is in Alarm Status. If you select

Always

, the TOP LED will always illuminate.

•

Glance Mode Setting

(see also paragraph 8.4). The Glance mode setting defines the colour of the TOP LED

and of the digits displayed in Glance Mode. If you select

White

, the TOP LED illuminates in white colour

(according to the criterion selected in TOP LED setting) and the digits displayed in Glance Mode are white.
If you select

Dynamic

the colour of the TOP LED and the colour of the digits in Glance Mode follow the

colour coding reported in 8.1.3.

Tip

►

To swap between Icon and Glance mode press on the icon

(see paragraph 8.4).

8.2.8.6

Factory Reset

To reset the display settings, press on the icon

(see Figure 89 a) and press

Start

to confirm (see Figure

89 b).

Figure 89. Settings

–

Display - Factory Reset (a - b).

8.2.8.7

Password

Press on

Password

icon

(see Figure 90 a) to access to password settings page and flag on

Password

Enabled

to enable the password use (see Figure 90 b).

Figure 90. How to enter the Password menu (a - b).

Note

►

The default password is okolab.

Содержание UNO-T










































































Результаты поиска

Содержание UNO-T

Отзывы:

Похожие инструкции для UNO-T

Бренды по названию

Популярные бренды

Okolab UNO-T, Руководство пользователя

Результаты поиска

Содержание UNO-T

Отзывы:

Похожие инструкции для UNO-T

Бренды по названию

Популярные бренды