Okofen PELLETRONIC TOUCH Скачать руководство пользователя страница 55 | Manualshive

Страница: 55 / 108

background image

Heating circuits settings

55

21

Heating circuits settings

Heating circuits settings

is in the Main menu.

Heating circuits settings has following menu items:

• Mode

• Room Temp Heating

• Room Temp Set back

• Time Allocation

• Values

• Time 1

• Time 2

• Party

• Vacation

• Heating Curve

• Screed programme

See customer menu

7 Heating Circuit, page 16

The additional menu items

Heating circuits settings

are for the ÖkoFEN Service

technician. The icon setting appears in the menu Heating circuits only after the code
input. Touch the Icon

Setting

to reach all other adjustable parameters.

Max Flow temperature

Set the maximum flow temperature to the chosen heating circuit.

Min Flow temperature

Set the minimum flow temperature to the chosen heating circuit.

Temperature increase

(System heat loss
adjustment)

Set the boiler or accumulator temperature above the set flow temperature of the
circuit calling for the highest temperature.
E.g. Set at 5°C with a heating/DHW circuit with a set temperature of 60°C the
minimum boiler / accumulator temperature will be set to 65°C.
The boiler does not start when boiler/accumulator is above the minimum temperature.

Mixer Yes/No

Choose type of valve used to control heating circuits.

Heating circuit with mixer motor or direct heating circuit

Mixer open– rest – close

Is the opening / rest / closing time of the mixer.

Boiler load range

The mixer opening speed increases with boiler temperature in the set range.

E1389EN 2.0

Operating manual Pelletronic Touch

«
...
53
54
55
56
57
...
»

Содержание PELLETRONIC TOUCH













































































































Отзывы:

Нет отзывов

Похожие инструкции для PELLETRONIC TOUCH

Бренд: Danfoss Страницы: 85

VLT Decentral FCD 300

Бренд: Danfoss Страницы: 112

Бренд: Danfoss Страницы: 4

VLT 6000 series

Бренд: Danfoss Страницы: 27

Бренд: Danfoss Страницы: 16

Бренд: Danfoss Страницы: 20

ADAP-KOOL AK-PC 781

Бренд: Danfoss Страницы: 14

Бренд: Danfoss Страницы: 12

Бренд: Danfoss Страницы: 12

vlt soft starter mcd 500

Бренд: Danfoss Страницы: 96

Бренд: jablotron Страницы: 22

Бренд: jablotron Страницы: 2

Бренд: Laird Страницы: 38

Бренд: Laird Страницы: 5

Бренд: National Instruments Страницы: 8

Бренд: Panasonic Страницы: 8

Бренд: DigiPower Страницы: 27

Бренд: GEA Страницы: 13

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды