Okofen PELLETRONIC TOUCH Скачать руководство пользователя страница 73

Страница: 73 / 108

Pellematic settings

27.1 Measuring values

Measuring values

is in the Pellematic menu.

It displays all measuring values of Pellematic:

• Actual values

• Set values

• Inputs (sensors)

• Outputs (pumps, mixer and motors)

27.2 Ignition settings

Ignition settings

is in the menu Pellematic.

Ignition settings has following menu items:

• Burner Auger Run Time

• Rest Time

• Burner Fan

• Flue Gas Fan

• Hyst Flue Gas Temp

• Min Flue Gas Temp

• Max Flue Gas Temp

The additional menu items

Ignition settings

are for the ÖkoFEN Service technician. They are present after

entering the code:

Burner Auger Run Time

Run duration of the burner auger during the ignition period,
expressed in tenths seconds.

Rest Time

Rest Time of the burner auger during the ignition period,
expressed in tenths seconds.

Burner Fan

Speed of the combustion air fan during the ignition period.

Flue Gas Fan

Speed of the flue gas fan during the ignition period.

E1389EN 2.0

Operating manual Pelletronic Touch

Содержание PELLETRONIC TOUCH













































































































Результаты поиска

Содержание PELLETRONIC TOUCH

Отзывы:

Похожие инструкции для PELLETRONIC TOUCH

Бренды по названию

Популярные бренды

Okofen PELLETRONIC TOUCH, Руководство по эксплуатации

Результаты поиска

Содержание PELLETRONIC TOUCH

Отзывы:

Похожие инструкции для PELLETRONIC TOUCH

Бренды по названию

Популярные бренды