Okofen PELLETRONIC TOUCH Скачать руководство пользователя страница 25

Страница: 25 / 108

Domestic hot water (DHW)

It can operate up to three menu items in

DHW

. Domestic hot water includes all parameters and settings for hot water

production .

DHW

is in the Main menu.

DHW has following menu items:

• Mode

• DHW Boost

• Water Temp Set

• Water Temp Min

• Values

• Time programme

• Time 1

• Time 2

Mode

Off

Set water temperature is reduced to 8° for frost protection.

Auto

Domestic hot water will be heated to the set temperature during time periods.

The system heats up the domestic hot water continuously on the Water temp set.

You can change the mode domestic hot water only when the

Operation mode

is on

AUTO

DHW Boost

Heats the hot water once on the Water temp set.

Water Temp Set

Set the water temperature.

Water Temp Min

Set the minimum water temperature. The water temperature never falls below this value,
unless the domestic hot water mode is

OFF

Values

You see all the DHW corresponding measuring values.

Time programme

Activate

Time 1

(= Time programme 1) and

Time 2.

Time 1 and Time 2

In the DHW time programme you set the times of the hot-water processing. The DHW
time programme works the same way as the heating circuit programme. See chapter

7.2

Time programme Heating circuit, page 17

E1389EN 2.0

Operating manual Pelletronic Touch

Содержание PELLETRONIC TOUCH













































































































Результаты поиска

Содержание PELLETRONIC TOUCH

Отзывы:

Похожие инструкции для PELLETRONIC TOUCH

Бренды по названию

Популярные бренды

Okofen PELLETRONIC TOUCH, Руководство по эксплуатации

Результаты поиска

Содержание PELLETRONIC TOUCH

Отзывы:

Похожие инструкции для PELLETRONIC TOUCH

Бренды по названию

Популярные бренды