Okofen PELLETRONIC TOUCH Скачать руководство пользователя страница 53

Страница: 53 / 108

Software

19.3 Update Heating Controller, Touch Operating device and Remote Control

The update is for the heating controller, the Touch operating device and the Touch remote control

Firmware Update — Approach:

Switch off complete heating system.

Take the touch operating device out of the
control panel.

Plug in the USB flash drive with the new
software in the back of the slot:

USB 0

of the

heating controller.

Place the touch operating device in the control
panel.

Switch on the heating controller.

Go to the

CODE

button, enter the code to

reach the level settings.

Go to the button

Software

Choose

Update

Note

If you have forgotten to insert the USB stick
- Press the

Refresh

button (wait about

1min)

Select the appropriate software.

10. Press the Button

Update

and reply to the query

with

YES

19.4 Software Update

First perform a software download. In the ÖkoFEN download area is always the current software available for
downloading.

Link: http://ftp.pelletsheizung.at

For access information, please contact your ÖkoFEN representative.

E1389EN 2.0

Operating manual Pelletronic Touch

Содержание PELLETRONIC TOUCH













































































































Результаты поиска

Содержание PELLETRONIC TOUCH

Отзывы:

Похожие инструкции для PELLETRONIC TOUCH

Бренды по названию

Популярные бренды

Okofen PELLETRONIC TOUCH, Руководство по эксплуатации

Результаты поиска

Содержание PELLETRONIC TOUCH

Отзывы:

Похожие инструкции для PELLETRONIC TOUCH

Бренды по названию

Популярные бренды