Okofen PELLETRONIC TOUCH Скачать руководство пользователя страница 16

Страница: 16 / 108

Heating Circuit

contains all relevant parameters and settings. It can operate up to 6 heating circuits.

Heating Circuit

is in the Main menu.

Heating Circuit has following menu items:

• Mode

• Room Temp Heating

• Room Temp Set back

• Time Allocation

• Values

• Time 1

• Time 2

• Party

• Vacation

• Heating Curve

Mode

Off

Only the frost protection function is active.

Auto

The boiler starts heating automatically according to the set room
temperature.

Heating

The boiler heats constantly accordingly to the Set room temperature.

Set back

The boiler heats constantly accordingly to the Set back room
temperature.

The operating mode of the heating circuits can only be changed if the plant operating mode
is set to AUTO.
The adjusted heating limits and maximum flow temperatures are used in all operating
modes.

Room Temp Heating

Choose your room temperature (Temperature within the heating times).

Room Temp Set back

Choose Room Temp Set back (= Minimum temperature beyond the heating times).

Time Allocation

Activate

Time 1

(= Time programme 1) and

Time 2

Operating manual Pelletronic Touch

E1389EN 2.0

Содержание PELLETRONIC TOUCH













































































































Результаты поиска

Содержание PELLETRONIC TOUCH

Отзывы:

Похожие инструкции для PELLETRONIC TOUCH

Бренды по названию

Популярные бренды

Okofen PELLETRONIC TOUCH, Руководство по эксплуатации

Результаты поиска

Содержание PELLETRONIC TOUCH

Отзывы:

Похожие инструкции для PELLETRONIC TOUCH

Бренды по названию

Популярные бренды